Jump to content
SAU Community

Hdi Super Boost Controller - Evolution

Hybrid-HDi
 Share

Recommended Posts

Hybrid-HDi Contributor

Hybrid-HDi

Posted
Posted

HDI-SBC-D-EVOLUTION

hdi%20sbc-d-evolution.jpg

ONLY $329.00 for MEMBERS

PLUS $20.00 Shipping Australia Wide.

HDi Super Boost Controller Type-D EVOLUTION

SBC-D-EVOLUTION

This boost controller has been designed for universal fitment to any turbocharged vehicle. The HDI-SBC-D-EVOLUTION provides the driver with precision boost and accurate display and measurement.

Product Features:

  • HDi Super Electronic Boost Controller with Dual in cabin adjustment
  • Closed loop boost regulation
  • Fast target boost locking
  • 120psi Pressure balanced solenoid
  • Micro Processor controlled
  • Rigid aluminum casing
  • HDi SBG-D Plug & Play Boost Gauge with Day & Night theme
  • Peak hold and recall function (with HDI-SEBS)
  • Dual read out both Digital & Analogue Display
  • Dual Measurement PSI & BAR
  • Full 270 Degrees sweep dial provides superb visibility
  • Advanced full electronic stepper motor drive
  • High Intense light emit diode back light for high visibility
  • Universal easy installation

Product Function:

The HDI-SBC-D-EVOLUTION uses a high precision temperature compensated pressure sensor providing the precision pressure reference for your turbo boost control function. By employing a unique closed loop boost regulating technique, the boost fluctuation is minimized once the desired boost level is reached. The anti lag program minimizes turbo spooling time so that you can have Fast, Sharp acceleration while maintaining your ideal regulated boost level. The HDi Super boost Gauge Type D (HDI-SBG-D) employs advanced stepper motor technology for accuracy and fast response. Our dual display design shows both BAR and PSI in analogue and digital format simultaneously. This provides the driver with easy and precise read out in the shortest possible time.

PLEASE NOTE:

Hybrid Development International Pty Ltd (HDi) is the official and legal owner of the TRADEMARKS, Hybrid and HDi Logos. HDi has been manufacturing Hybrid Performance Products since 1994.

HDi does all its own Design, Testing & Manufacturing (D.T.M). We are not associated with any other company nor do we source our parts through another company or make them in the same factory. You are dealing direct with the manufacturer and not a middleman. Since June 2007, we no longer have a sole distributor in Australia. This company had its dealership terminated due to hi jacking our trademarks and patents which is poor business conduct, this has been legally pursuant. We would also like to point out we have never stopped production or changed our name to release a new product. We have re-established our own operation in Seven Hills, Sydney, PH: 02 9620 7388

  • 6 months later...
  • 2 weeks later...
  • 6 months later...
Hybrid-HDi Contributor

Hybrid-HDi

Posted
  • Author
Posted
Is there any chance of just getting the boost gauge?

Hi,

Thanks for the enquiry. The gauge can be purchased separately. However, please note it will only work with our HDI-SBC-D(SE) boost controller. The gauge is $80 plus postage.

Thanks

  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • joshuaho96
      Automatic Power Button Light Flashing

      By joshuaho96 · Posted

      Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...