Jump to content
SAU Community

Recommended Posts

I have been having issues with my car going into R&R mode I installed a PFC recently and had it tuned (unigroup), now what I have noticed is two tings my car now has a hesitation/pause, almost light somethings cutting the power this comes every now and again I think its always been there but its only noticeable with the power FC (don't think its in the tune). My knock reading on the power FC will go as high as 112 but the engine light does NOT come on at all. I think this hesitation/pause has always been there, but possibly the tune has made the hesitation more noticeable. Its seems to only do it on light acceleration. And the knock reading wont go above 38 at any other time. I am thinking the fuel pump is on the way out???????? Also the engine light attached to the power fc knock system is set at 60 is there a way to check its on/set at 60. Any suggestions?????

Link to comment
https://www.sau.com.au/forums/topic/229196-strange-hesitationpause/
Share on other sites

First up, I'd talk to Yavus about what he thinks about your hesitation, as he clearly would have noticed it.

What turbos have you got - surge maybe?

PFC's don't have RR.

112 knock is bad, don't do it.

Datalogit / power excel to check the knock flash setting.

Fuel pressure gauge should show a f.pump weakness.

Edited by GeeTR

I have std turbos, I know Power Fc don't have R&R it was doing it on my std computer it just wasn't noticeable (cant think of any other reason I was having R&R too coincidental) and sometimes it will have this hesitation and not read any knock ???? i would have thought Yahulz would have picked it up as well but they wouldn't do a power run on very light throttle and its intermittent, and as I said the power fc is not reading knock and showing me on the dash light as I have never seen the engine light come on. Dont have datalogit. yeah i should give him a call but i dont think its got anything to do with his tune its an unrelated problem but he is the man to see. its just miles away from where i live.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...