Jump to content
SAU Community

Tomei Prepared Cyl. Head

Tomei_Powered
 Share

Recommended Posts

Tomei_Powered Rising Star

Tomei_Powered

Posted
Posted (edited)

RB25DET TOMEI Prepared Cyl Head consist of

1. TOMEI 1.2mm MLS H/G

2. TOMEI PROCAMS 260 Degree 10.25mm (IN)

3. TOMEI PROCAMS 260 Degree 10.25mm (EX)

4. TOMEI 10.25mm Type B Valve Springs (Out of production. TOMEI doesnt manufacture 10.25mm for RB25DET anymore. Mine was the last set)

5. TOMEI Solid Lifters Conversion

6. TOMEI Adjust Shims (Requires machining and hell of a hectic job to measure 24 shims)

7. TOMEI Cam Pulleys (IN and EX)

8. Ported and Polished Head.

Parts were bought brand new. Not even 4 months old. All parts were basically sitting in engine room.

Cylinder head was only driven for less than 1000km till my oil pump gave way and wrecked my bearings.

Ive purchased a whole GTR engine and im rebuilding my GTS everything from scratch again. Sigh..

Machining and the tedious job to measure shim precisely cost me a bomb!

Trust me, you wouldnt want to go through buying the parts your own and

have the parts installed. Its takes too much time and frust to get this cyl head prepared.

Price @ $3100.00. PM me for any details on the cyl head. You can check the items thru tomei-powered.com

post-43735-1217007538_thumb.jpg

post-43735-1217007553_thumb.jpg

post-43735-1217007585_thumb.jpg

post-43735-1217007598_thumb.jpg

post-43735-1217007621_thumb.jpg

post-43735-1217007637_thumb.jpg

post-43735-1217007657_thumb.jpg

Edited by Tomei_Powered
Link to comment
https://www.sau.com.au/forums/topic/229690-tomei-prepared-cyl-head/
Share on other sites
  • 5 months later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...