Jump to content
SAU Community

Recommended Posts

Hey, number of times ive been pulled over and straight away a cop thinks i have a turbo'd R34. Yet when i point to the Compliance plate they realised its a non-turbo when i point out the missing "T" on RB25DE ..

Now, when they think its turbo, they pop the hood and then look for the turbo.. on the left hand side of the engine -.- ..

So i was wondering if this could be an oppotunity for me?

Hook up a turbo to the RB25DE.. try to conceal it.. and have a side mount.

And if a cop asks.. the compliance plate says it all.

Not really considering this idea.. just a little thing i would like to discuss with you guys :)

What ya'll reckon?

MRXTCZ

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/
Share on other sites

iv been thinkin bout this 1 for a while. im tempted to try do it. i recon you could hide it with a custom low mount manifold. mate of mine is on his red p's and has a vl turbo n he jus snapped the bonnet release cable an put another 1 in the glovebox. works a treat jus gets defected for the bonnet cable but nothin an extra 50 cant fix.

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4043955
Share on other sites

thered be a bit of work involved, and you wouldnt be able to run high amounts of boost to keep it stealthed or through a sidemount...imo there wouldnt be much point until you can really go all out and get a proper setup. but hey if you wanna run the risk then by all means :sick:

ED: if you havnt already done so MRXTCz, i suggest you blank out all numberplates from photos you have hear...just incase they go snooping

Edited by G0DZLR
Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4044423
Share on other sites

youll be able to run about 9psi with the stock 25de bottom end.

but great idea, ive thought about it too.....havnt got the guts to try it out.

want a clean record so i can apply for a turbo exemption next year.

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4044494
Share on other sites

i have most of the parts to do this conversion for sale hint hint... :sick:

i reckon its a great conversion for someone that is handy on the tools and can just bolt all the parts up, there was a bloke that i met at the drags that did this conversion, made 260ish rwhp on stock turbo and shaved over 2 seconds off his 1/4 mile time. Not too shabby

Edited by R34GTFOUR
Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4044666
Share on other sites

If you were to run a low mount with a heat shield, the turbo would be near impossible to spot. NA cars have heat shields on their exhast manifolds too. You could run a reasonable flowing dump, high flow cat and good mid muffler. Just leave something stock-looking on the rear, and make sure its quiet.

Just make sure you stock-looking intake piping, which is all hard plastic rather than shiny metal, and with a standard plumb-back BOV. Paint the sidemount matte black and, if they ask, tell them its an auto tranny cooler because you like to tow stuff (getting a tow bar would help with that).

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4044705
Share on other sites

Wow thats great. Its a good concept i guess, but how would i keep the turbo silent. Wouldnt it spool up. Or would it be so quiet that i can make it a sleeper. Muahaha!

And what you mean theyre gonna come lookin' for me because i got mah plates on the forum?

MRXTCZ

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4044807
Share on other sites

Wow thats great. Its a good concept i guess, but how would i keep the turbo silent. Wouldnt it spool up. Or would it be so quiet that i can make it a sleeper. Muahaha!

And what you mean theyre gonna come lookin' for me because i got mah plates on the forum?

MRXTCZ

stock ballbearing turbo's dont make much spool noise, with a stock exhaust manifold, quiet exhaust, stock intercooler, piping and airbox, with stock boost, you'll barely hear the spool at all, and with no bov, there shouldnt even be an audible compressor surge...

Keep everything neat, quiet, nothing shiny, everything covered, and dont thrash the pants off it or attract attention, and i'd doubt you will ever have a problem with the popo.

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4045635
Share on other sites

Hmmm.. Im suddenly starting to consider this lil' concept lol.

Can i hook up a boost controller by any chance?

Say to vary it. When i wanna cruise to when i wanna just give it a beating ?

MRXTCZ

You will have to conseal it pretty well.. in case they controller says something like "Turbo Boost Controller"..

But I dont see why not?.. I mean if you get caught.. thats licence gone.. so Im sure that a Boost conroller won't be your's or their biggest worrie

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4046368
Share on other sites

i like the idea but id be worried at wearing out all the parts alot faster and blowing the engine thats what turns me off also it would be a bit pricey to do unless you can install it all yourself which is something i cant do.

ive herd that the r34 side mount intercoolers can handle alot of power so they would come in handy to keep the stealthy look.

quick story for whoever wants to read. I was driving to work the other day and a plain looking el ford pulled up beside me at the roundabout, we kept driving and i could hear he had a little exhaust looked over and it didnt look like much at all until he put his foot down a little bit more and i herd a high pitch noise, turned to take a look and it was him and he just took off , something i wasnt expecting at all it was definately a stealthy set up just the sound gave it away.

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4046988
Share on other sites

i like the idea but id be worried at wearing out all the parts alot faster and blowing the engine thats what turns me off also it would be a bit pricey to do unless you can install it all yourself which is something i cant do.

ive herd that the r34 side mount intercoolers can handle alot of power so they would come in handy to keep the stealthy look.

quick story for whoever wants to read. I was driving to work the other day and a plain looking el ford pulled up beside me at the roundabout, we kept driving and i could hear he had a little exhaust looked over and it didnt look like much at all until he put his foot down a little bit more and i herd a high pitch noise, turned to take a look and it was him and he just took off , something i wasnt expecting at all it was definately a stealthy set up just the sound gave it away.

just like a mate of mine, used to own an EA falcon. AU 4.0 motor, ran a highmount GT3540, black upsidedown FMIC, wolf ECU etc. you wouldnt know it was turbo till he put the foot down and kicked it sideways and let off for the massive dose :P.

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4047114
Share on other sites

Wow thats great. Its a good concept i guess, but how would i keep the turbo silent. Wouldnt it spool up. Or would it be so quiet that i can make it a sleeper. Muahaha!

Aim for silence. Most dead stock turbo cars have a near-inaudible turbo. Knowing that you have to run a quiet and stock looking exhaust with a sidemount means you know you're not going to be making big numbers, so work around the idea that you're just going for more power than NA rather than lots of power.

The turbocharger muffles exhaust noise to a certain extent, so if you got two proper mufflers in your exhaust then it'll be quieter than NA. A small bb turbo sucking through a factory airbox with low boost should be inaudible unless you happen to be right next to a cop with their window down at speeds low enough for wind noise not to muffle it. With the factory plastic piping and plumb-back BOV, its not likely to make a noise when you lift off the throttle either.

Its going to have to be a sleeper. That's the whole point to avoid the cops.

Going for low boost and all these NA restrictions, which choke the top end and outright power, also means that the power delivery should be reasonably smooth and predictable...which means your car also obeys the spirit of the P plater restrictions that is trying to get cars that are difficult to drive out of the hands of novices. It won't stand up as a defence, of course, but if you do get sentenced you could ask for consideration based on that sensibility.

On the other hand bear in mind that, if you've got a stealth turbo and you're not allowed to drive it, you've basically got no insurance. Even if you don't have comprehensive if you collect someone, there's a possibility that your CTP won't pay out. Getting stuck with someone's medical bills will practically f**k you for life.

As such, I wouldn't do it. Learn to drive what you've got and be patient.

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4047256
Share on other sites

A stock turbo on the N/A engine is mostly on boost, they're actually more whiney than a normal GTT. My one used to huff and puff all over the place :P

probably because they're working harder, feeding more power, due to higher compression.

Maybe find slightly larger ball bearing turbo? VG30?

On the other hand bear in mind that, if you've got a stealth turbo and you're not allowed to drive it, you've basically got no insurance. Even if you don't have comprehensive if you collect someone, there's a possibility that your CTP won't pay out. Getting stuck with someone's medical bills will practically f**k you for life.

Very unlikely, unless your in a serious crash and some one dies/is critically injured and your car needs to be looked over by forensics, no one will ever know whats inside it. Whenever you crash usually its just your job to collect your car and deal with it, unless your comprehensively insured, in which case if they find out about the turbo (which once again is unlikely, since its a non turbo chassis, and i doubt they'll check over the engine mechanics, just obvious things like tyres). So imo, your pretty safe, about as safe as most of these people with FMIC, Bigger turbo's, after market management, and other modifications that aren't legal or engineered. On top of that, Insurance company's like just cars, will still insure you, even if the car isn't mod plated, as long as they are aware of the modifications, your only concern would be MAIB, which would never find out.

I knew someone who crashed a VL into a wall at like 100 clicks, both people in the car have taken MAIB insurance for all its worth (and needed it) and the car was far from legal. (suspension, brakes, tint, rims, na+turbo, fmic, list goes on).

obviously though, you could be the one person out of thousands that doesn't get away with it

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4049729
Share on other sites

probably because they're working harder, feeding more power, due to higher compression.

Maybe find slightly larger ball bearing turbo? VG30?

Hell no, it was fun....I'd recommend it to anyone. High comp turbo engines are great, sounds like you're driving a steam train :)

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4049883
Share on other sites

Hell no, it was fun....I'd recommend it to anyone. High comp turbo engines are great, sounds like you're driving a steam train :)

haha i had that on my high comp 3L with a kkr430, anything over 1/5 throttle over 2000rpm and it would spool, 1500rpm under heavy load, was a bit of fun cruising up a hill in 5th on 1/4 throttle hearing nothing but spool at ~ 1600rpm (at fullboost - 5PSI) like driving a truck! (30e had low end cam in it and shaved head)

Link to comment
https://www.sau.com.au/forums/topic/230127-turbo-in-na/#findComment-4049940
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...