Jump to content
SAU Community

Recommended Posts

hi guys

I have a alarm system and the remote doesn't seem to operate as it should.

thought randomly it works fine.

I assumed it was the battery, but when I replaced it it was still the same.

anyone have a rough idea of what may be the issue or is it simply the fact my remote is stuffed?

If there is anymore information I need to share to assist with someone helping me.

please let me know.

Regards

Sloane

Link to comment
https://www.sau.com.au/forums/topic/230330-alarm-remote-not-operating/
Share on other sites

I have the smae problem wuth my remote.

I used to try changing the battery, I now just crack the shits and tap the remote on something...... lol not the best fix, but it makes me feel better :)

If any one knows a way to fix this issue,I would also be greatful for the information.

yeah mate had the exact problem with a customers car at work. pulled it apart and found two dry solder joints. resolder them and it worked like a treat. if you are good with a solder iron then give it a go cos if you take else where they will tell you to replace the remote.

Same god damn problem with me aswell!

Curse the previous owner who had to install a shitty eBay alarm grrr !!

Solder it aye? Hmm.

And what if that doesnt work lol ?

I played around with the 2 dials in the remote..

Didnt do anything for me.

MRXTCZ

Curse the previous owner who had to install a shitty eBay alarm grrr !!

Solder it aye? Hmm.

Don't touch it unless you have a back up plan if you stuff it up lol

I notice its been working fine when I point remote to engine direction :ermm:

I remember I've got a Spare Remote but its at a relatives so will have to pick it up.

I lurk on a huge list of forums, lol.

And your dead right, dont try to fix the remote if you dont have a fail-safe plan, that's just asking for trouble, and will put you into a bad situation.

With my previous car, someone installed a cheap ebay POS alarm, and wired it in quite stupidly, so I had the car towed (became unstartable) to an auto electrician and set him to task to remove the mess and set the car back to stock.

He did this, and then I went and got a proper alarm system installed in the car.

B.

  • 3 weeks later...

hey guys

stupid remote not working again

i tried my spare remote to see if it worked and didn't do anything either....

now I'm getting all sorts of weird beeping and basically have no friggin central locking meaning i need to open door via the key.....

and to start my car now I have to put key in ignition

set the alarm off then press remote to disable immobiliser and alarm (only time it seems to work)

just to start my car!!!! :sleep:

I'm going to ring the installers tomorrow who installed the alarm about the issues I'm having.

I got this installed on 25th January 2008

spent about $2200 at their workshop

Just curious as to whether they should fix this issue under a warranty?

Can some please verify that.

If all goes down the drain I will be seeing Chris Rogers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...