Jump to content
SAU Community

Recommended Posts

hey guys, i was planning to use a rb20/25 afm on my sr20 set up. i was aiming for about the 300 mark but i wanted to know if the rb afm can be tuned that high.

any advice/ info would be much appreciated.

thanks alot!

I have 240rwkw on the RB25 AFM. I think that's about the effective limit. Of course, you can go as high as you want but it means that you lose resolution at the upper end, and the problem with that is that your tuner has to tune to the 'worst case' scenario once your AFM is maxed out. What that essentially means if that you are not able to milk the most power out of the entire rev range.

In short, if you are aiming for 300rwkw then don't mess around, get a Z32 afm.

Link to comment
https://www.sau.com.au/forums/topic/233260-rb2025-afm/#findComment-4090207
Share on other sites

mmm.. thats right just get a z32... if you have the money to get to 300rwkw safely(im assuming your after) then you definetly can afford a z32...

or are you putting every last cent into a new turbo or forgy engine ?:rofl:

Link to comment
https://www.sau.com.au/forums/topic/233260-rb2025-afm/#findComment-4090268
Share on other sites

I have 240rwkw on the RB25 AFM. I think that's about the effective limit. Of course, you can go as high as you want but it means that you lose resolution at the upper end, and the problem with that is that your tuner has to tune to the 'worst case' scenario once your AFM is maxed out. What that essentially means if that you are not able to milk the most power out of the entire rev range.

In short, if you are aiming for 300rwkw then don't mess around, get a Z32 afm.

oh i didnt meant 300kws, i ment 300hp, so this should be fine rite

Link to comment
https://www.sau.com.au/forums/topic/233260-rb2025-afm/#findComment-4090664
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...