Jump to content
SAU Community

Recommended Posts

1996 R33 Nissan Skyline Series 2 Manual GTS-t - $11k

Car is in good overall condition with minor scratches here and there. The car made 220kw ATW when dynoed by the previous owner. This car is a fantastic sleeper and is mechanically sound. You will not find an R33 Series 2 with as many modifications and as much power as this one for this price.

Modifications:

* Microtech ECU (no AFM).

* Aftermarket High-Flow ball baring Turbo (VG30 Nissan housing). steel wheel internals

* Turbo-back exhaust with Apexi Cannon.

* Apexi Boost Gauge.

* Momo 18 inch Wheels with 265 wide tyres on front and back.

* Trust Gear Knob.

* R33 GTR Front Mount Intercooler (painted black).

* High-Flow Fuel Pump (brand unknown).

* Alarm and Immobilizer.

Faults:

* Minor scratches here and there (best to come inspect).

* Missing front left indicator/foglight.

* Missing grille.

Mark - 0438 416 584

post-18827-1220326669_thumb.jpg

post-18827-1220326674_thumb.jpg

post-18827-1220326679_thumb.jpg

post-18827-1220326684_thumb.jpg

post-18827-1220326691_thumb.jpg

post-18827-1220326699_thumb.jpg

post-18827-1220326731_thumb.jpg

post-18827-1220326735_thumb.jpg

Edited by mook1
  • 3 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...