Jump to content
SAU Community

Recommended Posts

Make: Nissan

Model: Skyline ECR33 Sedan - Impul R33R complete car, number 136 of 200

Milage: 95,000km - genuine, with extensive records back to new from Japan

Transmission: Manual

Colour: Impul Silver

Location: Sydney

Complied? Yes

RWC supplied?

Currently registered? About to expire, will lapse as going into storage when I move

Price: $13,995

Contact: Gareth 0401-325-953 or [email protected]

You are looking at a genuine Impul R33R. One of a limited run of 200 vehicles made by prestigious tuning house Impul (of Calsonic Impul GTR racing fame) this one is stamped with number 136 in interior and engine bay.

It's based on an R33 Sedan (RB25DET) and is an original 5 speed manual. It's a complete tuning package including:

- Full body kit

- 17" wheels

- Handling package - strut brace, sway bars, suspension

- Full interior, front & rear seats. Beautiful Impul steerting wheel.

- Exhaust

- Computer (included in sale, but has been replaced with Power FC)

It also has:

- Trust Intercooler

- Apexi Air Filter

- HKS EVCIII and Power FC (Tuned by CRD - 200.5kw at rear wheels)

- Nismo Carbon Gear Knob & Razo Pedals to complete the interior.

I imported the car from Japan through J-Spec about 12 months ago. It has full service records back to new and is in genuinely immaculate condition.

The car owes me over $22k. Urgent sale as I am leaving the country, you will nowhere find better bang for buck than this at just $13,995.

post-39849-1220530931_thumb.jpg post-39849-1220530970_thumb.jpg post-39849-1220531035_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/234793-r33-sedan-must-sell-only-13995/
Share on other sites

What a beautiful car.....if only i had enough funds for this beast. Im surprised no one is snapping this up!!!

Whats the go? why arent there any takers? any feedback to the seller?

Edited by starion4me

Hey, thanks for your comments. I can't believe it either - I took one look at the photos of this in Japan and just had to have it!! It has been such a good car too. It's painful to let her go so cheap!

Almost wondering if I should take her back to Japan with me when I go???

This car is sex :blink:

Do you have any pictures of the rear with the impul spoiler? Me thinks I want one... and some of those sexy side skirts awell.

It's a shame you have had to reduce the car by so much. I see people on here saying they can't find manual r33 sedans WELL HERE IS A GENUINE IMPUL ONE FOR THE SAME PRICE AS A NORMAL ONE!

Tell me about it!! Here's a couple of rear/side on shots (I have literally thousands of photos of my car to choose from, sad, I know!). Gives a good look at the spoiler & sideskirts anyway.

Good news to any potential buyer... the person who will look after her for me has agreed to get rego done, so will no longer be selling unregistered, you now have brand new 12 months rego too!

post-39849-1221047868_thumb.jpg post-39849-1221047978_thumb.jpg

Come on someone... genuine Impul, original manual, 4 door Skyline!!

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...