Jump to content
SAU Community

Recommended Posts

hey guys

got an r33 gtst with stock looking rims, except the rears are 7.5" wide, fronts 6.5" (as pointed out by the tyre shop)

i've getting some bad understeer on the track. will this drastically change if i upgrade to wider front (and rear) wheels? or am i better off putting $1000 into swaybars / subframe alignment / camber etc?

cheers

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/
Share on other sites

I would first look at getting the swaybars as you can then change the characteristics of the chassis and they will make the biggest difference as they will also reduce body roll.

When money permits I would go as wide as you can with wheels ie. 8.5 front, 9.5 rear.

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4123011
Share on other sites

id be looking around for some cheap 2nd hand wheels, maybe a few hundred $$ worth, go at least 16" diameter and something up around at least 8". when i say cheap i dont mean tempe specials, i mean good lightish brand name wheels, just cheap in price (whether it be due to looks, gutter rash etc). chuck some decent wide tyres on them and upgrade the sway bars.

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4123067
Share on other sites

i was actually wondering if anyone could say if and why the stock rims are bad for track use

stock rims are thin, u cant fit as large tyres on them, its basically that simple.

for track use u have to remember the tyres are being put under higher force, so if u put wide tyres on thin wheels, ull have the tyres flopping around all over the place as there is less strength holding the sidewalls upright. if u have a wider rim and put a same size tyre on, the walls will be sit nice and vertical or slightly pulled in which keeps the sidewalls more rigid which obviously transfers to more responsive steering.

although then there is the issue of unsprung weight, but tbh i think thats less of an issue.

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4125034
Share on other sites

heres a question

just say you are running a 235/45/17 on a 9" and a 7.5" rim would you notice a difference between the two?

yes, big difference. the 9" will have more rigid sidewalls and movement of the tread will transfer more directly into the wheel and in turn the steering. this can mean u get tracking where the wheel follows the road more, not great for highway driving but great for steering response.

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4125042
Share on other sites

i guess the theory of wider wheels / tyres is pretty simple. but can anyone quantify the difference (perhaps when they have upgraded to wider wheels)?

as in, have people felt there was a WORLD of difference in turn in ability when they have gone from 215 to 245 front tyres (for example)?

just like this thread (except this one is all about swaybars);

http://www.skylinesaustralia.com/forums/In...rs-t235329.html

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4125151
Share on other sites

yeah you're right

i guess if i think about it logically, its going to be $1600 - $2000 for some rims and OK rubber

full swaybars are going to be $500ish

so the wheels option is going to cost about 4 times more than swaybars. will it give 4 times the benefits? i doubt it... (but could be wrong)

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4126591
Share on other sites

toyo t1r's

however they are 225's up front which are a little too wide. i could take them off and put 205's to reduce sidewall flex, but i'd loose contact area.

would i notice a huge improvement by downsizing tyres, or would it be better off investing the $400+ on tyres into swaybars? argh....

:P

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4127301
Share on other sites

swaybars are ur best bet, but as i said u dont have to spend big $$ on rims, just buy smart. something like this:

http://hardtuned.net/forums/index.php?showtopic=333667

there are much better examples around obviously, and if need be u can just buy 2 pairs if they are dirt cheap.

quality rims, decent width, and if u buy well u could probably get away with a similar set for less than $400.

but yeh, go the sway bars first.

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4127374
Share on other sites

would i notice a huge improvement by downsizing tyres, or would it be better off investing the $400+ on tyres into swaybars? argh....

Tyre profile would be far more noticeable than changing tyre size on your rim. That said, swaybars will make a significant difference. By themselves, they will improve the cornering ability of your car noticeably, but once you've stiffened up the roll rate through tightening adjustable swaybars, you can back off your dampers and enjoy the benefits of better roadholding mid-corner as your shocks can now do a better job of absorbing bumps, rather than being set hard to stop body-roll.

Swaybars are my suggestion.

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4127421
Share on other sites

hmm is it legal to have mismatched rims on the street?

there are no ADR's requiring the wheels to match front and rear.

saying that u are only allowed to go 1" wider and increase the track by 26mm (13mm each side), so pretty sure legally your limit is a 18x7.5 +27. those rims i showed u are legal besides being 1/2" over width, but no cop should be able to tell what width they are. in other words if u get defected for them, u were gonna get defected for them regardless of whether they were legal or not as the officer cannot tell what size they are from the outside (unless the size is stamped on the outside of the disk).

Link to comment
https://www.sau.com.au/forums/topic/235428-wheel-width/#findComment-4127700
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
    • EDIT: PSA to whoever stumbles upon this thread. It is in fact a crack in the block that caused this concern. Just letting you know. In my case, a few cm long hairline crack going horizontally above the turbo oil feed. Classic RB shit I guess
    • Might as well pop in some cams, head gasket, head studs, and a flex sensor. Full send.
    • Yeah I spent close to a year finding one. I was even tempted to buy a RB25DE N/A head and port it out. That latter option, could still be an option.
×
×
  • Create New...