Jump to content
SAU Community

Recommended Posts

Item: R32 5 point Cusco bolt on half cage

Condition: Very Good

Price: $550 ono

To Fit: (What car) R32 Gtst or Gtr

Location: Adelaide

Comments: Comes with all bolts, nuts, plates etc.... ready to bolt on.

post-18416-1221394153_thumb.jpg post-18416-1221394177_thumb.jpg

Edited by Richo
Link to comment
https://www.sau.com.au/forums/topic/236060-r32-cusco-roll-cage/
Share on other sites

  • 2 weeks later...
wont fit dude
^^^ as he said mate, it wont fit! back legs sit on the wheel archs.

hmmm thats weard i put this tomie 2 door cage in my 4 door

unless my mate 2 door had a 4 door cage in it

it was easy to install as well with the 4 doors an all lol

07102008178.jpg

07102008179.jpg

28092008172.jpg

yeah i dont see why it wouldnt fit, the chassis is basically the same as a 2 door with just another door added in to get into the back

maybe get this bloke to get some measurements to see if it will mount like the one above GTS4WD

it will fit if u make it, but it sits too far back!

if u think about it, if the car rolls, all the weight/force will go straight to the drivers/passengers head while ur back seats will be protected!

i would think the 4 door and 2 door have the same floor pan

it bolted to the same place than the 2 doorwe had them next to each other

strate out of 2 door in to the 4 door same holls same place

and it looked the same

but i cant rember where the top bar went over the head rest in the 2 door

but my seats are just a bit forwared than normal in the pics

also the rear door handels just hit the cage when i close them

Edited by dreadr31

yeah from memory both 2 door and 4 door cages will fit each other, if you look at the size of the front doors from 2 door and 4 door, the 2 door is longer,

so if the 2 door cage sits at the pillar it will sit a bit behind the pillar in a 4 door, but will still connect to the wheel arch and then the distance to the dash will be the same as it sits further back,

so it should fit 2door and 4door

JV

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
    • Well, I had an Edward Lee's special edition odo windback car/motor with a RB25DET S2 and I put down 372kW with a good amount of track abuse for 1.5 years before the ring lands decided it didn't want to stick around anymore 🥲 But probably didn't help I kept on smashing try limiter on the track and a few skid pans.
    • That is correct,  I have a forged RB25/30det NEO hiding away safely and I wanted to use the very rare greddy vct adj cam gear on this new setup and so I just used the whole thing on my s1 instead of pulling it appear because I'm lazy af 😅🤌🏼
×
×
  • Create New...