Jump to content
SAU Community

Recommended Posts

Hi guys, just before i go on my spiel i would like to thank everyone who showed patience through the whole saga, it was not only frustrating for everyone else but also for myself and Adrian too. Big thanks has to go to Pete (SLED) for helping us out also. Kudos also to those who whole-heartedly supported us, it means alot to us.

Now, this may not be the outcome that alot of you want, but IMO it is the best outcome we could have hoped for at this stage.

The printing company, VELFLEX, has agreed to supply us with a blank replacement for each hoodie/jacket. This includes us being able to keep the ones we have. Steve (MADAZ) has generously agreed to take over the printing for the blank hoodies, but your old and new hoodie is your property now, and you do not have to have the reprinting done.

Once again, apologies for the whole situation, i accept that the current hoodies are not what we wanted. Im hoping everyone can move on from this and we can all be friends and hold hands :banana:

From Adrian and Damo :D

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/
Share on other sites

  • Replies 310
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Cheers heaps for you hard work Damo and Adrian even if i did have a little sook

for the price of these next hoodies im sure you guys wont mind forking out a little again and i will put a small markup on the hoodie so i can donate some money to Christian for the running of the forums but when i nail everything down i will let everyone know and make a thread in the Group buy section

yeah my plans involve embroidery the firm I'm looking @ will probably be better for a complete they supply and embroider so with what we have now im going to wait till we can get some local quotes for embroidery as we dont want to pay for freight 3 times

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/#findComment-4148485
Share on other sites

awesome work guys, very happy with ya work.

cancel my comment i like madaz idea :banana: will look a lot more profesh in my opinion and prob cost like 2bucks more. the crap they printed with on the jumpers i reckon is better suited to t shirts only

but awesome work none the less all

Edited by Inline 6
Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/#findComment-4148500
Share on other sites

yea no shit! for a company to f**k up so hardcore, then give us a blank hoodie in negotiation isnt that dodgey to anyone else! not a dig at adrain or damo, but should we try negotiating and getting what we payed for not, paying $55 for a blank hoodie in the end! im sure you have been negotiating with them anyway, but should we try just a little harder?

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/#findComment-4149138
Share on other sites

lol boys it was fifty dollars so what we have to pay a bit more to get a great product im a single mummy and i dont care we are lucky to even get the blank ones anyway so you just need to pay for the embrodery so what now be good boys and pay madaz x

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/#findComment-4149140
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I think he was only proposing to use the wire, not the sender. Simply because it runs from the right place to the right place. Personally, I wouldn't hack up the factory wiring like that. I'd just lay in the Defi loom.
    • From memory it wasn't too hard to simply see which wire ran where when you plug that in. Unfortunately also from memory the OEM sender does not use the same configuration 99.9% of gauges run. So in other words if you connect the signal wire that was running to the OEM gauge to your DEFI gauge you might find your oil reads at 200C or some other incorrect value. I remember having the same line of thought and then running new wires/senders to match the gauges I have. The pinout is available in the R34 workshop manual.
    • Does anyone on here know which wire on the GTT triple gauge pod harness is for the oil temp gauge? my sensor works fine but I upgraded the gauges to DEFI advance. And if I can simply piggyback off the oem oil temp wire to the Defi oil temp sensor wire that would make life so much easier. 
    • Even face her a wash now that’s it worth more than my house
    • This was what I was invisioning, or Pete cutting a beer can up and hose clamping it around the catch can! Ha ha ha
×
×
  • Create New...