Jump to content
SAU Community

Recommended Posts

no way keep the badges - the boot is to boring without them - maybe with a nice lip spoiler it would be ok but otherwise... I would not have taken off the SKYLINE if you are keeping the NISSAN badge - I think all badges or none at all (with a spoiler) are the only options...

2892_rear_r_107.jpg

2887_rear_rl_234.jpg

  • 4 years later...

whats different about the 07 lights?

-mark

The only difference I see in regards to the '07 vs '04 lights is that the reverse lights on the '07 are rectangles.. They're clear round ones on '04 lights..

On another note, mine had the Nissan taken off, and an infiniti grill put on! I need to change that very soon, I think!

Edited by Ninja_Nate

The only difference I see in regards to the '07 vs '04 lights is that the reverse lights on the '07 are rectangles.. They're clear round ones on '04 lights..

On another note, mine had the Nissan taken off, and an infiniti grill put on! I need to change that very soon, I think!

03 to mid-06 lights

- flat face

- round reverse light

- halogen light for running light

- leds in circle for brake

- leds closest to boot lid are 4,4,4 pattern

mid 06+ lights

- they have 'recessed' areas over the lights - stove top design like R34' - not flat.

- square reverse light as stated

- led running lights in the circle

- led brake lights

- led's closest to bootlid are a 3,4,5 pattern

- boot release button on LHS light

i did a language conversion on a V35 coupe that had this badge..

the Prince skyline badge

looked pretty neat against the blue.

6283268655_af330ac5c6_z.jpg

hey mate how much do you charge for the conversions if I may ask? And you in Melbourne I presume?

can you PM me a cost?

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...