Jump to content
SAU Community

Ohlins Suspension/coilovers

RubyRS4
 Share

Recommended Posts

RubyRS4 Grand Master

RubyRS4

Posted
Posted

Modified Ohlins suspension from R33 to fit Stagea RS4

Has bottom eye mount points on all 4 corners. Fit to my Stagea easy (easy swap to do with jack/hoist). Replacing Ohlins with newer ISC coilovers, so no longer wanted.

$500 (not inc postage) prefer local pickup

:thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/237226-ohlins-suspensioncoilovers/
Share on other sites
BigDirtyJase Experienced

BigDirtyJase

Posted
Posted

hey Reuben,

Got a couple of questions for ya?

1. what was the ride like with them on - also do you have a pic of your car with them on

2. whats the condition of them

3. do they fit S2 Stageas

4. what's ride height on it

RubyRS4 Grand Master

RubyRS4

Posted
  • Author
Posted
hey Reuben,

Got a couple of questions for ya?

1. what was the ride like with them on - also do you have a pic of your car with them on

2. whats the condition of them

3. do they fit S2 Stageas

4. what's ride height on it

1. The Ohlins is a little too stiff for me. Adelaide is full of potholes and bad road works. I'm sick of the roads more than the suspension really.

Pic ...

house019.jpg

house017.jpg

About 350mm front and rear.

2. The Ohlins are in good condition. I won't say excellent. They don't leak, but they are filthy with road crap. I fitted them after purchasing them from JMS for twice as much. Only done about 6,000kms with me.

3. They are currently on an S2 Stagea. Had an engineer redo the rear hats to fit.

4. Ride height I have set for my stag is about 350mm front and rear.

I'll also be going thru Melbourne next week if you're keen and want to save on shipping. :rolleyes:

BigDirtyJase Experienced

BigDirtyJase

Posted
Posted

I'm keen, I've been looking for suspension for ages (other than SK's Group Buy and Tein Super Wagons). Are they adjustable like Teins??

As I said i'm definitly keen - and if you're coming down to Melbourne than its a bonus

RubyRS4 Grand Master

RubyRS4

Posted
  • Author
Posted (edited)
I'm keen, I've been looking for suspension for ages (other than SK's Group Buy and Tein Super Wagons). Are they adjustable like Teins??

As I said i'm definitly keen - and if you're coming down to Melbourne than its a bonus

They are coilovers, so they are adjustable in height and dampening.

I've had a fair bit of interest in this, so first in , best dressed.

Update: I get my ISC coilovers today, so the Ohlins set will be removed this weekend, if not tomorrow night. :banana:

Edited by RubyRS4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...