Jump to content
SAU Community

Recommended Posts

ok i just sighned up because i have these parts for sale

rb26 head

chemically cleaned

deburred

planed

fully re machine

ported and polished

stock brand new valves

stock brand new retainers

brand new hks 272 10.2 lift cams

brand new hks valve springs

perfect condition has not yet been used

comes with plenum and throttle setup

cas

sensors etc

fuel rail

no injectors or cam covers

asking price $3200

will post anywhere at buyers expence

ems 8860 ecu brand new neer used has map for 26/30 cost 1850 im after 1650

stock rb26 head with plenum and throttles sensors wiring loom and std ecu no covers or injectors asking 1100

to4z surge slotted and ceramic coated rear housing asking 2300

turbosmart 48mm pro gate brand new never used asking 650

apexi power fc suit r33 gtst comes with hand controller was only used once on the dyno asking 1000

magnafual 1000hp fuel pump and billet filter cost 1k im after 800

rb26 ati balncer with billet anodised water pump pulley after 800

sard rb26 injectors twin spray 850cc asking 700

turbosmart 1200hp fuel reg 500

plasmaman custom intercooler 700 by 280 by 100 cost 1500 selling for 1200

rb25 head modded to suit rb30 block ready to bolt on comes with oil feed hose witing loom fuel rail injectors and sensors asking 1000

6boost custom highmount manifold to suit gt35/40 or any t3 flange turbo cost 1300 asking 1000

ati rb26 head studs cost 400 asking 300

billet anodised hks fuel rail 350

custom clatch built to handle 300rwkw daily drivable comes with flywheel suit rb 20 or 25 cost 650 after 500

ring me on 0409512048

  • 2 weeks later...

unfortunatley im in tasmania and my digital camera is rooted i may be able to go threw some extra trouble to get certain pics if somone is really interested and not a time waster power fc is sold

Edited by WPNVLT
unfortunatley im in tasmania and my digital camera is rooted i may be able to go threw some extra trouble to get certain pics if somone is really interested and not a time waster power fc is sold

can you please get a couple pics of the 2 x rb26 heads.

and pm me or post them up here either or.

very intersted just not sure which one.

what model are they 32? 33?

and why have they not got cam covers?

  • 2 weeks later...
bump make offers on anything very strong rb30 bottom end there will take 400rwkw price drop 3k delivered

there was no mention of an rb30 in the original thread. can u pm me pics and more info please?

oh oops i thought it was in there lol

it has

cp forged pistons to suit twin cam head 8.5 comp

h beam conrods

arp studs

it is 20 thou over

rb25 oil pump

new water pump

new main seal

repainted block

crack tested

were after 3k for it but if somone takes it this week ill pay postage witch will be over 200

sorry i havent been able to get my digital camera to upload pics every time i plug the card into my pc it freezes.

turbosmart gate now 600 delivered brand new

ati balancer 750 delivered brand new

magnafuel fuel pump with filter cost 1k now 800 delivered brand new

hks billet purple fuel rail 300 delivered brand new

sorry evocoop i dont really want to seperate the balancer from its pulley if you were able to find somone that wanted the balancer i would seperate after payment for both items was made

  • 3 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...