Jump to content
SAU Community

Recommended Posts

Hi all,

Im hopping some one can help with this we have recently picked up our V35 350GT8 2002, Most of the time the car is fine but twice the car has been on the Highway and twice the car has appeared to start slipping, ie. revs increase but the speed does not to the extent that the car is doing 100klm/h and doing 4500rpm (there is still drive there) at which point I pulled over let the car sit for a minute then once we had taken off it was fine.

Has any one heard of this before???

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/
Share on other sites

Hi all,

Im hopping some one can help with this we have recently picked up our V35 350GT8 2002, Most of the time the car is fine but twice the car has been on the Highway and twice the car has appeared to start slipping, ie. revs increase but the speed does not to the extent that the car is doing 100klm/h and doing 4500rpm (there is still drive there) at which point I pulled over let the car sit for a minute then once we had taken off it was fine.

Has any one heard of this before???

Without specifically knowing anything about that box, I suggest you need to find out what oil you need, as this could be an issue.

As per a Motorbike with a wet clutch plate, the wrong oil can cause no ends of problems, especially slipping.

If you have the wrong oil you can destroy these clutch plates and from how I understand the box is not that well known in Oz, as for repairs!

Research the oil and make sure that is the type inside, would be my first step.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168403
Share on other sites

Without specifically knowing anything about that box, I suggest you need to find out what oil you need, as this could be an issue.

As per a Motorbike with a wet clutch plate, the wrong oil can cause no ends of problems, especially slipping.

If you have the wrong oil you can destroy these clutch plates and from how I understand the box is not that well known in Oz, as for repairs!

Research the oil and make sure that is the type inside, would be my first step.

Thanks Stephen,

I will do that but its not so much a case of slipping but when this happens it it slike its decreasing the gears available and it wont flip to manual mode

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168423
Share on other sites

when was the last time it was serviced and what oil was put in?

to my knowledge they use a special oil. its been covered here a few times now.

general consensus on the CVT is to stay away from them when buying for that reason.

lately I have been seeing cheap sedans only to find they are all CVTs with I figure half dead boxes.

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168487
Share on other sites

maybe its not the gear box, maybe theres an issue else where, the car will only drive in 3rd gear when in limp mode, ie theres a major issue somewhere, 100kmph at 4500 kinda sounds like 3rd gear

Yes that sounds about right Pete,

any ideas what would make it go in to limp mode after being driven for some time with no issues then to do it only on very odd occasions ??

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168970
Share on other sites

when was the last time it was serviced and what oil was put in?

to my knowledge they use a special oil. its been covered here a few times now.

general consensus on the CVT is to stay away from them when buying for that reason.

lately I have been seeing cheap sedans only to find they are all CVTs with I figure half dead boxes.

Thanks Chris,

Have you heard of this specific porblem before??

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168976
Share on other sites

Yes that sounds about right Pete,

any ideas what would make it go in to limp mode after being driven for some time with no issues then to do it only on very odd occasions ??

I'm guessing and if it isn't Oil (which is my number 1 pick) and without seeing the wiring diagram but a loose or bad connection and/or faulty speed sensor or input to the Gearbox Computer.

Could be a multitude of stuff unfortunately, but you have to start with the easy stuff first such as Oil and then check continuity of all the connections...

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4169003
Share on other sites

Just wondering if it occurred when you're happening to go downhill? It may be of no help but when I'm at 60km/h down a slight slope (albeit a short one) I tend to let my foot off the accelerator and let the car cruise by itself. The car tends to increase its revs slightly (to around 1500 if I can remember, from the normal 1100/1200rpm) until it reaches a falt surface where the revs drop back to the normal 1200rpm. If so I think it's just a normal occurence.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4169146
Share on other sites

Hi Just to share my point of view. As you all know, CVT(Continuously Variable Transmisson) box have no gears in it. The Jap box usually use a belt to run on the 'virtual' 8 gears. I know there is quite a few porblem with the CVT box from Honda. The CVT box is design for city use and not for hard acceleration. The CVT in AUDI's cars (Muliti-tronic) are different too, they do use a series of gears but they are chain driven. From the description of the problem when driving above 100km/h, I believe the belt will tend to slip. That why if you keep pushing, it will just slip more. I think it's best to let someone to look into it for you. And BTW, they do have a Torque Convertor in a Nissan.

Edited by FlyingEL
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4169808
Share on other sites

when was the last time it was serviced and what oil was put in?

to my knowledge they use a special oil. its been covered here a few times now.

general consensus on the CVT is to stay away from them when buying for that reason.

lately I have been seeing cheap sedans only to find they are all CVTs with I figure half dead boxes.

Spot on.

If you use anything other than the factory recommended Nissan Gearbox oil for the CVT, its history.

Replacement costs are not friendly either.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4170087
Share on other sites

Hi Just to share my point of view. As you all know, CVT(Continuously Variable Transmisson) box have no gears in it. The Jap box usually use a belt to run on the 'virtual' 8 gears. I know there is quite a few porblem with the CVT box from Honda. The CVT box is design for city use and not for hard acceleration. The CVT in AUDI's cars (Muliti-tronic) are different too, they do use a series of gears but they are chain driven. From the description of the problem when driving above 100km/h, I believe the belt will tend to slip. That why if you keep pushing, it will just slip more. I think it's best to let someone to look into it for you. And BTW, they do have a Torque Convertor in a Nissan.

Nope - the V35 uses a very different type of CVT gearbox - they call it the 'Extroid CVT', basically uses a sliding set of angled gears to acheive the same thing as a belt.

http://auto.howstuffworks.com/cvt3.htm

The rest of the Nissan range uses a belt type CVT (Murano, Maxima etc).

Getting back to the original problem, these guys might be able to help:

http://www.cvt.co.nz/index.htm

They're pretty much the only ones in this neck of the woods that know anything about the Extroid CVT, the Nissan dealers will likely only be familiar with the belt type.

Sounds like the gearbox controller is detecting something wrong with the gearbox and putting it into 'limp' mode. Not sure if there is a diagnostic mode for the controller that might allow you to work out what is wrong? When it gets into this mode does it flash anything on the dash cluster?

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4172104
Share on other sites

Nope - the V35 uses a very different type of CVT gearbox - they call it the 'Extroid CVT', basically uses a sliding set of angled gears to acheive the same thing as a belt.

http://auto.howstuffworks.com/cvt3.htm

The rest of the Nissan range uses a belt type CVT (Murano, Maxima etc).

Getting back to the original problem, these guys might be able to help:

http://www.cvt.co.nz/index.htm

They're pretty much the only ones in this neck of the woods that know anything about the Extroid CVT, the Nissan dealers will likely only be familiar with the belt type.

Sounds like the gearbox controller is detecting something wrong with the gearbox and putting it into 'limp' mode. Not sure if there is a diagnostic mode for the controller that might allow you to work out what is wrong? When it gets into this mode does it flash anything on the dash cluster?

good work and great advice...

still think the first step would be ensuring the right oil is inside.

Edited by Stephen Thorpe
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4173643
Share on other sites

  • 4 weeks later...

My cousin is having the exact same problem on his 2003 v35 sedan with 8speed CVT.

He can't get the car to change gear, and the engine seems to not like revving over 4,500rpm. I believe that the car is in limp mode.

The oil hasnt been changed to the nissan cvt one. Would we go into the dealers and ask for another models car gear oil (e.g another nissan with CVT) and just buy the oil from that...?

Any help would be appreciated. It has been off the road for a while now.... Your help is greatly appciated

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4226227
Share on other sites

Take the car back to who ever you bought it off as their are issues with high klm GT-8's and tell them to sort it, the oil is $1,500 and $26,000 for the gear box from Nissan Australia (last time I checked Nissan Japan don't stock them).

They overheat which causes a few issues but the materials used are not up to standard as they have various failures, the guy in NZ repairing them makes his own parts that have failed as they are not available Ex Nissan.

I can go on all day about why they fail, why the were released in Japan only and other problems but just do a search and everything is mentioned.

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4226913
Share on other sites

  • 5 weeks later...

Thanks for all the advice guys.

Took it back to the dealer and they said thery could not fault the box but, They SAY they changed a solanoid, but they couldnt produce the solanoid (convenient)

By the sound of things they are hopping the car will be out of warranty by the time I have a BIGGER issue

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4290102
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...