Jump to content
SAU Community

Recommended Posts

Hey,

I recently installed one of these clutches on my GTR.

When i first drove it, it bit like a b*h. Very little take up, had to ride it a bit so it wouldn't stall. Whilst changing gears, if i wasnt cautious, it would chirp all 4 and feel like the wheels were going to rip off.. lol

However, i noticed a real change after i had put approx. 145km on the clutch. The "chirpiness" disappeared and it seems like the clutch has lost its angry bite.

The clutch is still good and doesnt slip or anything, but has just lost that angry bite. (clutch now has 350+km on it)

Im just wondering if this is what other people have felt and if its normal. If not, what could have caused this?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/238682-exedy-twin-plate-clutch/
Share on other sites

Nah, never did...having said that i've got some really good rubber and a very aggressive camber, castor, toe out set up for the track, so it takes a bit to get it to chirp. Only thing i can think of is it will chirp less as the clutch beds itself in maybe?

I have the exact same clutch as you, for around 3000km now.

I have found that over time as the clutch beds in it becomes more and more drivable, and less aggressive although still grips very very well.

Another interesting thing is that for the first 500km when you depressed the clutch pedal there was a very loud plate rattle.

This is almost completely dissipated now, which is good.

Exedy twin plate in my 89 GTR with about 10,000km of daily driving on it.

Still bunny-hopping around town like an idiot because the bite is so hard and take-up is so short.

Also ridiculously heavy for my weedy legs, which might have something to do with it. :/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...