Jump to content
SAU Community

Recommended Posts

Hi Guys,

Anyone know the (replacemant), Bosch ten digit part number for a GTR fuel pump? Are R32/R33 GTR'S the same pump.

I have to change the pump in my GTS-t 33, and was told to get a GTR pump from Bosch, but no-one knows the part number!

Can anyone help PLEASE!!!!!!

Many thanks in advance!!! :) :)

Link to comment
https://www.sau.com.au/forums/topic/23904-gtr-fuel-pump-part/
Share on other sites

I didnt think skyline fuel pumps were made by bosch?????

If you get a bosch 910 (less than $300) they will fit and give you alot more head room than a stock fuel pump. A bit more fiddley to fit than a GTR pump, but not alot of farking around like a 044. A cheaper option than a GTR pump.

A second hand GTR pump, expect to pay around $400 retail secondhand, a bit cheaper if you shop around or bargain, but they are a direct fit and will take only about 1/2 hour to replace. Good for 250rwkw.

Hi guys, R32GTR, R33GTR and Z32TT are the same fuel pump, they flow 190 litres per hour which is good for around 420 bhp.

The closest in the Bosch Motorsport range is 0 580 254 910 (generally called a 910) they flow 200 litres per hour, good for 450 bhp. Then there is the 975 , 984, 040 and 044 (which is good for 730 bhp). Just add "0 580 254" in front of the above 3 digits.

We buy ours from Repco.

Hope that helps

Remove stock pump, lay the pump and metal bracket on a piece of cardboard and trace around it.

This is very important, as it will make sure you get the stock pickup in the same spot with the aftermarket pump.

Next remove the pickup from the stock pump (small circlip), and remove the pump from the bracket. Trim the plastic that is used to secure the pickup to the pump via the circlip. Use a short piece of fuel line (8mm? from memory) to secure the 910 to the pickup, use hose clamps to secure the hose.

Get two small round crimp type connectors for the fuel pump to connect the wires to the pump. I am not sure if it is a banjo fitting for the 910 or hosetail, but you will need a connector for the top of the pump (I did a 044 not 910). You may need slightly larger fuel line, depending on the size of the connector. From here you connect the supply line to the pump. Once again use hose clamps

Attach the pump to the bracket. Place a large (3") hose clamp around the pump and bracket. Make sure the pickup is in the same spot as the stock one was - using the traced outline on the cardboard. Tighten the clamp (or 2 clamps if you are paranoid about the pump coming loose.

And now you are right to replace the whole assembly into the tank - easy:)

Hi guys,

Thanks for the replies!

I was just wondering where you get you figures from in relation to l/hr flow rates!

I found this info on the bosch website which states otherwise!!!

http://www.bosch.com.au/sat/motorsport/dow...s/fuelpumps.pdf

I have been speaking to bosch and they say these are the maximum figures but may increase slightly but not to the extent some people may suggest!

I have heard people say the 044 is good for 500-600hp or V8 supercars, but does anyone know what the 910 is good for as it only flows 130l/hr @ 5 bar max, but may increase to 150l/hr @ around 3 bar, and as Bosch dont work by HP figures, it makes it difficult trying to get a pump for my supposedly 240 hp car!

Any other thoughts??

Thanks again guys!! :P;):D :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...