Jump to content
SAU Community

Recommended Posts

The head has been removed from the block, and I have started scraping old gasket muck from the block, but just wondering what I can use to make it shiny clean - I read in a yankie V8 rebuild book that they use a 1/3 sheet sander on the deck (not to remove metal, just cleaning it) Is this wise - would you use a fine grade paper and give it a quick once over?

Or should I give it a going over with some deagreaser or metho on a rag?

Or is there another method for getting it cleaned up?

Also, what is this aluminium spray they use on head gaskets? should I use it, or is there another sealant/gasket cement I should use?

-A mechanic looked at it an said it should be ok without getting the block or head machined, but I will have the head done for peace of mind. It is also getting a gasket kit, new water pump and timing belt.

Apologies in advance for the noob q's - What I need is a large print picture book :cool: Thanks all

Edit: forgot to mention, its an RB20DET

Edited by Medium Dave
Link to comment
https://www.sau.com.au/forums/topic/239196-my-first-blown-head-gasket/
Share on other sites

When I had to replace my head gasket, I just scraped off all the old gasket with a sharp blade. Just kept at it till the surface was nice and smooth. Before I reinstalled the head with new gasket, I gave it a wipe down with some metho to make sure it'll have a good contact without oil or anything getting in the way.

Whether or not you should use the spray to put the gasket on will depend on the gasket you buy. There was no need to use any extra seal with my gasket, but I've heard of others needing it before installation. I'm guessing it just depends on the gasket you purchase.

This was all done on a 4AGE Toyota motor (naturally aspirated), don't think it would be much different for an RB20.

Edit: I did this about 2-3 months ago and the motor's still running strong!

Edited by adam-__-

When I did mine (rb25) I went over it with some fine grade sandpaper and it got the block looking really good. The head I had machined as I wouldnt trust scraping away at the head (being a softer alloy could dent it easily).

That said, the car still isnt running so I cant say how well it has worked.

Would be interested to hear if others have used the sandpaper method as well?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...