Jump to content
SAU Community

Recommended Posts

Need quick replies please, i'll be doing this today!

I am putting some aftermarket gauges into my car:

Water temp, Oil pressure & Oil temp.

I already know that i can't remove the factory water temp sender near the thermostat housing, as this reports back to the ECU the engine temp. I've already had a friend fabricate an alloy "T" pipe to splice into the top radiator hose, with a fitting welded onto it to take the water temp sender. That's sorted...

But...

Would i be interfering with the ECU or car in any way by removing the stock oil pressure sender (just below the inlet plenum & AAC valve) and stock oil temp sender (behind the oil filter and close to the block) and fitting the senders that were supplied with the gauges?

I was feeling pretty confident that it was ok, before i had a closer look at noticed alot more wiring than i thought there'd be coming from these senders in the wiring loom...

Thanks for the quick replies in advance.

Link to comment
https://www.sau.com.au/forums/topic/23920-aftermarket-gauges-r32-gtr/
Share on other sites

Hmm, 31 views, no replies, thanks guys! :D

At least you can learn from my experiences here:

Well, i've fitted the oil pressure gauge with no problems at all, works well. Much better than the original gauge that has all sorts of problems reading accurately.

Only problem i did come across was that the OE Nissan oil temperature sender is a VERY obscure thread size. A very rare M12x1.25 thread. Realising that a 1/8"NPT threaded sender won't fit, i went to my local Enzed and had no luck with getting an adaptor. Same story at Pirtek, they said only M12x1.5 thread is the most common and doesn't even come close..

Plan B, decided to test the original Nissan sender against the sender supplied with the gauge. This involved getting out my multimeter, digital thermometer and tested the resistance of both senders at different temps in a saucepan of water on the stove!! :bahaha:

No good there, the senders both having completely different ohm ranges.

Plan C, tried looking through VDO's catalogue for an appropriate sender. Turns out that their only sender in the thread that i was after also had the wrong ohms range.

Looks like the oil temperature gauge stays off for the time being until i can figure out a way to get an adaptor fabricated or find a suitable means of fitting this gauge.

Any suggestions?

  • 2 weeks later...

I hate to bring back my own thread again, but, don't you hate it when you spend the time, money and effort in engineering a one-off part to do something (in this case an adaptor for a water temp sender) and you could have bought something like this:

hose_atc.jpg

But my reason for this post, was whether anyone has seen this oil filter sandwich adaptor for sale anywhere here in Australia? It would help me alot if i could get ahold of this product to help hook up my oil temperature gauge (as i discussed above):

sensor_atc.jpg

The following pic, you can just make out that it's the threads i need, M12x1.25 and 1/8"NPT.

It will need to suit the thread of the oil filter to suit an R32 GTR as well.

sensor_ill.GIF

Thanks.

  • 2 years later...

I ll bring this thread from dead again, for people's future information. Ring Mark from Motorsport Connections in Seven Hills, they can manufacture an adapter for oil/water temp/pressure.

Addr.: 15/4A Foundry Rd, Seven Hills

tel.: 98387272

I haven't had mine done yet (waiting for oil change). I ll post how I wen when they are done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...