Jump to content
SAU Community

Recommended Posts

K so i have GAB (Gabriel?) suspension on my r32 gtr and i am wondering how to adjust it.. It's just adjustable tension i'm guessing, not ride height.. The car looks like it's sitting standard ride height but the front barely bounces when i put weight on it, the back moves a bit more but not much, seems to be alot tighter than what i assume is standard. So i've uploaded a pic of what the adjusters look like.. i'm not sure if the ones on the nuts at the front work as they seem to spin really easily? Front don't seem to have an adjuster on the actual unit whereas back do.. There are settings between 1 and 8 on back nob, it was on 2, i reset to 5 noticed no real difference

any suggestions?

Thanks

post-26886-1223648228_thumb.jpg

Edited by GTAAAH
  • 3 months later...

GAB suspension is aftermarket. I had similar suspension on my R32 GTS-T. The knob on the rear struts and the twist knob on the top of the fronts adjust the dampening of the shocks. Adjusting it will have no impact on how "hard" the car will feel, it simply adjusts the rate at which the dampers control the oscillating spring. It does that by restricting the flow rate of the oil from reservoir to reservoir as the strut moves up and down. Essentially it restricts the rate at which the spring can move over a certain distance.

You can lower the car further by backing off the "C" nut on the struts but often it will sometimes actually taken preload off the spring (meaning that the spring will flop around when the car is jacked up. So most only height adjustable suspension have "helper springs" in them so that you can further lower the car without the spring becoming loose. Although I've found its not really a problem if the spring is loose in the strut anyway. It takes up the preload of the spring once the car is on the ground again.

Hope that helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...