Jump to content
SAU Community

Recommended Posts

hey in my r33 gtst s2 i have a bosch 040 , its been in the car since iv bought it and its always been really loud when priming and i can hear it every now and a gain while idling , the other day my mechanic said its too loud and on its way out. is this true cos iv read that 040's are really loud , should i play it safe and get a 044 or just not worry about it? cos i figured its been in for a couple years it should have stopped by now if something was wrong?

Link to comment
https://www.sau.com.au/forums/topic/241070-fuel-pump/
Share on other sites

Well aftermarket fuel pumps are usually a lot louder than the standard one. So I'm inclined to say its just normal. I found with my walbro and my mates 040 that on long trips the fuel pump gets louder.

And the way its mounted as mentioned can contribute to how loud it is. Mine is mounted with rubber in between the hose clamps and you can still hear it a fair bit when the cars not moving. If it has no rubber mounting it'll resonate even more.

A true way to check if its on its way out is to see if its running out of puff up high. So get the AFR's checked on a dyno or hook up a wideband O2 and check them yourself. Otherwise I'd say there's nothing wrong with what you've got.

Link to comment
https://www.sau.com.au/forums/topic/241070-fuel-pump/#findComment-4210188
Share on other sites

+1 for mounting issue.

I paid an extra $200 for sard instead of bosch for my GTR, so i could retain the nicely engineered mount. I still cant hear the pump. I think gtst pumps are mounted differently tho. Make sure all attaching parts are cushioned.

Edit: if priming's loud then the pickup is a problem. Do you notice the noise more when the tank is low?

Link to comment
https://www.sau.com.au/forums/topic/241070-fuel-pump/#findComment-4211823
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...