Jump to content
SAU Community

Recommended Posts

The opportunity arose to pick up a 32 4dr ex-drifter stripped car the same time I bought a written off 33... so the maths added up. This happened on the 9th October... The decision was made to attend drift attack at winton only 9 days later... Lack of sleep and some hard work resulted in the mods list and photos below...

Engine:

RB25DET Series 2 - Currently 261 rwkw @ 16 psi!

Exhaust:

Custom 3" Turbo Back

Apexi 3" EVC - Exhaust Valve Controller

3" x 100cm Resonator

5" Straight Pipe from Diff Back

Suspension:

Chopped Springs lol (for now - as it came)

Wheels:

Front Wheels - 17x8 Black DriftTeks

Rear Wheels - 17x9 Works for Drift, 17x9 Drifteks for Grip

Front Tires - Federal 225/45/17 - 595RS

Rear Tires - Peeling/Smoking/Disposable or for grip Federal 255/40/17 - 595RS

Modifications:

RB25DET Series 2 Engine Conversion

RB25DET Gearbox

R33 Engine Crossmember

R33 Gearbox Crossmember

Nismo Engine Mounts

Nismo Gearbox Mount

R33 Radiator

NPC Twin Plate Clutch

R33 Clutch Pedal / Master / Slave

Custom Tailshaft (Suit RB25 Gearbox)

Nismo 1.5 way 4.1 LSD

Modified R33 S2 Wiring Loom - Partially hidden/relocated

Aftermarket Tie Rods

Aftermarket Rod Ends

Adjustable Castor Rods

Cusco Rear Camber Arms

Urethane Sub-Frame Bushes (pineapples) set for traction

Hicas Lock Bar

R33 RB25 Power Steering Pump

R33 Power Steering Reservoir

Custom Boxed in Standard Castor Rod Brackets

Custom Castor Rod Brace (welded in)

Custom Chopped Springs & Unknown Shocks

S13 Steering Rack

Solid Steering Shaft Spacer

Steering Rack Spacers

TD06-20GL2 Chinese Copy (modified exhaust housing with T3 Flange)

XSPower High Mount T3 Ext Gate S/S Manifold

50mm Chinese External Gate

50mm S/S Screamer Pipe

HKS Same Holes Cooler Kit (old design - small core for response)

Custom Cooler piping made from assorted scap and offcuts smile.gif

4" Intake with 4" Pod Filter

Bosch/Nissan Z32 Air Flow Meter

Relocated AFM to Cold Cooler Pipe

Walbro Copy Intank Pump

Chinese Generic Fuel Reg

Momo Steering Wheel

Couple of Gauges

More to Be Advised.

Stereo Audio / Visual:

N/A

Estimated Power:

261 rwkw @ 16 psi

Day 1:

Clean engine bay, remove S13 crossmember, fit R33 crossmember, nismo mounts, dummy fit engine, remove old crap etc....

post-179-1224593068_thumb.jpg

post-179-1224593375_thumb.jpg

Day 2:

Dummy fitted turbo kit, fitted HKS front mount and made 1/2 cooler piping, remove engine, extract replace 4 broken exhaust manifold studs, block off water lines for oil only turbo, fit clutch to engine, fit engine & box, rapt to find that R33 Gearbox crossmember bolts straight onto RB25 box in R32! Also rapt to find that simply swapping the R33 front yoke of tailshaft straight onto R32 tailshaft will bolt straight up!

post-179-1224593642_thumb.jpg

post-179-1224593892_thumb.jpg

DAY 3:

Custom wiring loom finished, oil feed for turbo, custom tailshaft completed, oils & filters, plugs changed, just need fuel lines and oil drain and she's running!

Quiet day on the 32 today, had 4 cars to tune, then went down the beach for a few cans! will have some more progress tomorrow, then exhaust and finish cooler piping monday, hopin to have all finished by wed.

Day 4:

Cooler piping finished using random offcuts and scrap, only need to purchase 1 piece of silicon

Oil feed & Drain fitted to turbo

Wiring loom tidied up and partially hidden / relocated

Fitted 1.5 way Nismo LSD and shafts

Fitted Custom Tailshaft

Fitted 50mm screamer pipe - Venting of course smile.gif

Relocated AFM to cooler pipe

post-179-1224594133_thumb.jpg

post-179-1224594551_thumb.jpg

Day 5:

Exhaust done, snapped drive shaft testing twin plate sad.gif

Ok... so the TD06 works ok.

230 rwkw @ 12 psi (minimum boost) only revving to 6400 rpm as the standard injectors (cranked pressure through fuel reg) and standard afm.... Gate sounds great lol...

Tomorrow - Z32 AFM, more pressure (budget - might buy injectors later), wheel alignment, seat belts, wash it....

post-179-1224592507_thumb.jpg

Day 6:

More wiring done, OMP Bucket and Willans harness fitted, wheels/tires fitted, wheel allignment done...

As far as the power goes it's now difficult to estimate, with the rear work wheels we could only get 3.5deg neg, which makes traction difficult... Fitted a new Z32 air flow meter, turbotech boost controller, set boost to 16 psi and gave it a quick retune...

More fuel was needed, a lot more, so now the base fuel pressure is 70psi! (Not recommended - don't try this at home!)

Also decided a vernier cam gear may be a good idea to dial in some response... Only problem is that with the camber on the back, four straps, and the tires were still PEELING off at 254 rwkw...

PLANS: Primal Garage - Flare the Flared rear guards more, redo wheel allignment with less neg camber (I Hope) and fit the 255 Federal 595 RS to the back and see if we can get a decent power figure for the weekend...

post-179-1224592603_thumb.jpg

post-179-1224592746_thumb.jpg

Day 7:

General tidy up, wash car, flare, flare, flare guards... redo wheel allign with 0 camber on rear :P mmm traction...

Dyno 261 rwkw @ 16 psi

Overall impression so far - I LOVE THE WAY THIS CAR DRIVES!!!!

post-179-1224592796_thumb.jpg

Edited by Dr_Drift

hmmm , so the turbo is a trust td06 l2-20g copy right? , whats the response like? , i was planning on spilling out the big bucks for a genuine one but i might sit n watch how this thing goes first... Any plans on doing a trip to tassie with it? :rant:

hmmm , so the turbo is a trust td06 l2-20g copy right? , whats the response like? , i was planning on spilling out the big bucks for a genuine one but i might sit n watch how this thing goes first... Any plans on doing a trip to tassie with it? :D

Want to make a few changes, upgrade radiator and maybe some coilovers, and the gearbox is whining after the weekend... Will try and make next day at Basky!

As for the L2, yes it's an EXACT copy... we've completely pulled the turbo apart and put it side by side with a genuine L2 and you CANNOT spot the difference...

Response on the 25 is pretty stupid, and I haven't even hooked up the VCT!! More to be had :D

Pulled the intake pipe off this aftenoon, and with over 1000km now on it (most of it HARD) there is absolutely no signs of wear at all!

I'm negotiating direct with manafacturer to try and get these in a bit cheaper (dodgy exchange rate!) but I'm going to have to order min 10 pcs!

Drop me an e-mail, I'll give you few options... I modified mine to fit on a chinese T3 high mount ext gate manifold, but one of my suppliers also has Trust copy high mount manifolds, and can sort a few different gates etc etc..

I just went in this thing.... an absolute monster!... even with sam's best attempts at keeping traction .... as soon as boost came on he couldnt keep it down.... the response was fenominal! I truely am conidering selling my current setup and getting one of these turbos!

well done mate,

Good work!

Adam

  • 1 month later...
  • 2 weeks later...

Ok, so took the taxi out to calder for the drags... car has been retune to the tune of 305 rwkw!

Best ET was 12.0 @ 122 mph with a 2.6 60' and sever lack of traction!

R32 4 Door Burnout

R32 4DR 122 mph Fly By

Best MPH was 124, best 60' was 1.6 but snapped driveshaft on gear change and rolled just short of 400m

Did a good enough burnout to make the home page of fullboost :P

post-179-1228771259_thumb.jpg

post-179-1228771272_thumb.jpg

post-179-1228771287_thumb.jpg

post-179-1228771300_thumb.jpg

post-179-1228771324_thumb.jpg

post-179-1228771341_thumb.jpg

post-179-1228771356_thumb.jpg

post-179-1228771444_thumb.jpg

post-179-1228771458_thumb.jpg

  • 4 months later...

holy smokes! thats is one ridiculous figure for Chinese turbo id say!

is it still going hard or what? can you pm me about the turbo and the setup you have, im very interested as im currently building a track car myself but am on a tight budget.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...