Jump to content
SAU Community

Recommended Posts

ok i've tried a search on this and couldn't find anyone else asking about the same problem

I have an R33 gtst 4 door S1. The drivers side power window can go down, but doesn't go back up. The motor is fine, you can hear it spinning.

Now i've pulled it apart to try and see what was wrong and i can't see anything wrong. I can manually push or pull the window up and down and the cable thing turns all ok.

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/241752-r33-power-window-not-going-up/
Share on other sites

Pretty common problem, few things it could be

mine was a combination of the relay and the door button panel.

to get it up in the mean time, take your battery out and put it next to the door, then take the door trim off, theres a little plug that you can disconnect that goes to the motor which goes through a hole.

wire up the positive and negative to the battery and touch them on the terminals going to the window motor, if it doesnt work then switch the terminals.

i stripped back the ends of some speaker wire and twisted them together at each end (obviously not the same one that goes to each terminal)

once that's done you probably just need a relay, either that or the button is locked on auto, it's a common problem like i said.

find out which door button panel you have, theres one with a black backing and one with a white (they're different wiring structure if i remember)

but go to an import spares place and just try a relay and a button panel individually, see where the problem actually lies. mine was unluckily in both

good luck

im not convinced its an electrical problem, as i can quite plainly hear the motor working when try to put the window up

i have got a complete motor and cable mechanism on its way from a wreckers now though, so just be replacing everything this will solve my issues

im not convinced its an electrical problem, as i can quite plainly hear the motor working when try to put the window up

i have got a complete motor and cable mechanism on its way from a wreckers now though, so just be replacing everything this will solve my issues

what i suggested to you would have confirmed whether the problem layed in the electrics or the motor/regulator

mine clicked nonstop when mine was the relay

from my experience it goes down cause theres less effort on the motor than pushing it back up. It will sound like its dying when you listen to it. If you do the direct power test as mentioned it would tell you if your motor is on its way out or if its the relay/switch.

i have the same problem in my r32, do i have to take the skin off to test the circuit or is the plug in between the jam of the door ? or in the car ?

im pretty sure the r32 doors are similar layout to r33, im not sure about the skin, but you'll see a small double plug that you can just pull apart and feed 12v down the pins going to the window motor

between the door trim and the shell of the door

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...