Jump to content
SAU Community

Greddy Coilovers Bnr32 Gtr

DRFTAE86
 Share

Recommended Posts

DRFTAE86 Enthusiast

DRFTAE86

Posted
Posted

Hey guys i have brand New GReddy Type S Coil Overs. I bought these recently from a ebay seller but they were incorrectly listed for an ER34. They DO NOT fit an ER34!~ So they are of no use to me. Unfortunetly i had already payed for them and it was to much of a mess around to get my money back. :(

I took the set to a GReddy dealer with a part number obtained from the previous owner. With the help of the GReddy dealer, the part number given indicated they are for a R32 GTR. (Part number: 14022204). The spring rate listed is also 8kgs front and 6 kgs rear.

The studs on one of the top hats is also a little smaller in diameter to the other side at the front for some reason? Which is still usable as is, has no affect on the installation or use of the coilovers. But if you aren't satisfied you could just replace the studs with the right size or use your own top hats as i was told by greddy.

This set will also supposedly fit a HNR32 (non GTR R32) as well.

This set has never been driven on. I did *try* fit them to my R34 for, but it became quickly clear there were slight differences so they could not be installed. So they are virtually out of the box!

This set retails for $2020 and thats when the AUS dollar was still strong. With the current exchange rate the set would cost closer to $3000! So grab your self a bargain! :(

Feel free to ask me any questions ill try help best i can. If you need measurements or things like that just let me know. Also inspections are welcome. I'm not too familiar with skylines. :mad:

Location: Melbourne South East.

Postage available at buyers expense.

Price: $1400

post-20413-1225018655_thumb.jpg

post-20413-1225018667_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/241839-greddy-coilovers-bnr32-gtr/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...