Jump to content
SAU Community

Recommended Posts

i dont know if this is normal or not but when i start my car up the revs go over 1000rpm and in a split second they go down that low its like the engine is struggling to get the revs back up so i give it a bit of a rev and it goes back up but there is this weird tic tic tic noise under the bonnet?

its due for a major service but it has done this for a little while now,any ideas???

the only thing i can think of is i got it serviced by a mechanic a while back... just the oil and oil filter and he could have put some cheap ass oil in it.

Link to comment
https://www.sau.com.au/forums/topic/243170-r-33-gts-t-series-1-engine-bay/
Share on other sites

i dont know if this is normal or not but when i start my car up the revs go over 1000rpm and in a split second they go down that low its like the engine is struggling to get the revs back up so i give it a bit of a rev and it goes back up but there is this weird tic tic tic noise under the bonnet?

its due for a major service but it has done this for a little while now,any ideas???

the only thing i can think of is i got it serviced by a mechanic a while back... just the oil and oil filter and he could have put some cheap ass oil in it.

if i thought that my oil was too thin/cheap i'd go str8 out and buy some nice oil... saaaaay motul turbolight 4100 10w40 and an oil filter... saaaaay a ryco z145a and do an oil change that day...

jus sayin.......

I have the same problem. On my fc hand controller it says that my vct sensor is turning on and off. Its located on the right of injector number 1, and looks like a goldy coloured hexagonal tube thing with a plug in it. That is the clicking that i can hear in mine. It also makes my idle hunt terribly on start up, but then goes away after it gets warm?? :D Let me know how u go, or if i find a solution ill let u know!!

Edited by RB JET

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...