Jump to content
SAU Community

Recommended Posts

Make: Nissan

Model: BNR32 GTR

Colour: White

Location: Vic

Complied: Yes

Currently registered: Yes

Price: $23500

Contact: 0433821257/Leave MSG/PM -------->> no joy riders or tyre kickers...........SERIOUS BUYERS ONLY

Just done the major service --------->> timing belt, air con belt, drive belt..

MODS:

-APEXi PowerFC+Hand Controller

-BLITZ i-Color EBC

-HKS GTSS turbos

-HKS Type-R Intercooler

-HKS Intercooler Piping Kit

-HKS Fuel Rail Kit

-Nismo Fuel Pump

-Nismo 320km/hr Speedo

-N1 Water Pump

-Sard Fuel Regulator

-Tomei Cam Gears

-D2 Coilover

-Super Advan Racing 17*9

-SplitFire Coil Packs

-DBA 4000 series disks (front) DBA slotted disks (rear)

-57mm Aluminium Radiator

-2wd/4wd switch

-z32 AFM x 2

P.S. NO SWAPS and more photos at: http://www.carsales.com.au/used-cars/priva...=3&__Nne=20

post-6374-1225780688_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/243275-1992-bnr32-gtr/
Share on other sites

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...