Jump to content
SAU Community

Recommended Posts

Hi guys,

Contact details:

phone - 0411408841

email - [email protected]

location - Redcliffe QLD, 20 minutes north of Brisbane

have for sale :

Genuine Recaro Reclinable Seats

Do not have seat rails, but do have mounting points.

One mark, size of 5c coin on left seat, slight fading on sides, otherwise in great

condition. No tears or holes.

Looking for $500 for both. Pick up only.

post-13752-1226279535_thumb.jpgpost-13752-1226279549_thumb.jpg

post-13752-1226279559_thumb.jpgpost-13752-1226281158_thumb.jpg

Wheel Spacers

1 pair of 15mm spacers - $70 (missing one nut)

1 pair of 20mm spacers - $80

1 pair of 5mm spacer plates - $15

Complete set - $150

Looking to sell as a complete set

Pickup or post

Suit skylines and other cars using a PCD of 5 X 114.3

Came off an R32 gtst I imported from Japan and filled out the gaurds nicely with the standard gtst rims.

Would be ideal for those looking to fill their gaurds using stock rims or for drifters.

post-13752-1226279622_thumb.jpg post-13752-1226279634_thumb.jpg

post-13752-1226279646_thumb.jpg post-13752-1226279660_thumb.jpg

GTR Intercooler

I think it is off an R32. Core has some damage to the front lower section, as pictured.

Price - $80

Pickup or post

post-13752-1226279878_thumb.jpgpost-13752-1226279894_thumb.jpg

post-13752-1226279911_thumb.jpgpost-13752-1226279926_thumb.jpg

Regards

Ryan

  • 2 weeks later...
  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...