Jump to content
SAU Community

Recommended Posts

Hi guys,

Sadly I need to sell my Evo VII because I'm heading overseas for a while. It's pretty much stock standard so there's tonnes of potential to do it up. The engine still runs very strong. It's in excellent condition and always garage.

Aftermarket lightweight Enkei Rims, 3pt immobiliser, built in turbo timer.

Price: AUD$26,500 ONO

Kms: 66,000km

Reg Exp: MAY-2009

Location: Castle Hill

Contact me (Phylis) on 0466 359 915 to arrange for an inspection :P

or email me to [email protected]

Especially for those enquiries from interstate, here's a link to more pics.

http://s453.photobucket.com/albums/qq253/p...Small%20Images/

BEZ_04.jpg

<p>

DSC01447.jpg

Interior

DSC01420.jpg

Engine Bay

DSC01424.jpg

Giant horns that came with the car when imported from Japan.

post-52340-1226306255_thumb.jpg

post-52340-1226306293_thumb.jpg

post-52340-1226306302_thumb.jpg

Edited by phyl
Link to comment
https://www.sau.com.au/forums/topic/244171-evolution-vii-for-sale/
Share on other sites

stock my mates isnt as quick as my gst-t putting out 210wkw iv driven his and he agrees. but the potential with these cars is ridiculous. bit of boost, remap, exhaust and they become scary quick. good luck with the sale dude.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...