Jump to content
SAU Community

Recommended Posts

Yea but im sure that rb30 was build to handle 30+Psi lol

Can front wheels and covers be swapped over like rear ones?

Yes they can but you will find it is a very expensive exercise! Rear housing from Garret from memory was $600+

And yes +1 to a .63 housing being way to small on a 3L it will choke up for sure IMHO it is a bit of a misfit size in the Garrett range...

The .82 is not too bad on a stock RB25 more suited to a built motor but it will be a good balance between not having to buy a new turbo when you get the 3L cause a .82 on a 3L is a response monstor :domokun: I personally have a 1.06 rear on my 3L and wouldnt have it any other way as it feds on the power so nicely. Also I might add mine is internal gate and am having no problems with boost control 7psi actuator and a Turbosmart T and holds dead on 15psi.

And is it definately internal gate?

hahaha

Thanks for the info guys, For now i think im going to wire the Internal Gate shut, Mod my manifold to house an external gate and still use the .63 rear. I like it at the moment how i can cruise around at the moment like everything is normal but flat foot it off the line in first and it doesn't break traction. If the .63 generates too much heat ill put an external gate rear .82 housing on the turbo and keep it that was until i wack it on a 3L.

Thanks for the Info.

Hey guy,

I think 'the mafia" did a gt30 with a .63 rear end. Search for his threads. I dunno if you're already onto it, but it makes for a good read.

Also, just something I would consider if I was in your shoes... Why don't you use the GT35 with a ext gate setup until you get your 3.0l

from what everyone on hear says, the ext gate spools the turbo quicker, and then you have an upgrade path. You may or may not want a .82 rear house when you 3.0l, but that's then, not now.

Yes they can but you will find it is a very expensive exercise! Rear housing from Garret from memory was $600+

And yes +1 to a .63 housing being way to small on a 3L it will choke up for sure IMHO it is a bit of a misfit size in the Garrett range...

The .82 is not too bad on a stock RB25 more suited to a built motor but it will be a good balance between not having to buy a new turbo when you get the 3L cause a .82 on a 3L is a response monstor :( I personally have a 1.06 rear on my 3L and wouldnt have it any other way as it feds on the power so nicely. Also I might add mine is internal gate and am having no problems with boost control 7psi actuator and a Turbosmart T and holds dead on 15psi.

hahaha

You have the XR6T version yeah? with the 0.50 front cover?

How does that affect compressor flow?

You have the XR6T version yeah? with the 0.50 front cover?

How does that affect compressor flow?

I do but also have a .7 cover

There is no noticeable difference between the .5 and .7 without changing the tune, might get some gains when it gets retuned though...

I have found that bigger turbo's with low boost make heaps of wastegate air. So if the gate is too small, and or the waste gate dump is to small, the issue comes where the gate cannot dump enough gas to stop the turbo from spooling up.

yea we figured that one out, going external gate so will resolve that...I was talking more of whether the .63 rear can flow enough through it to cope with the gt35 front cover and the volume of air its producing to not create too much heat.

If i were in your predicament, i would seriously consider selling it and buying a proper matched turbo. As you seem aware, a 3082 is behind the 8 ball, as teh ex wheel is too small to generate enough torque to accelerate the rotating mass quickly. And by using a .63 exhaust, it is partially alliviating that, but adding high backpressure to the equation. I would be fitting a .82 3076, as IMO it is the ideal turbo for an rb25 after 280-300rwkw. Even if you fit the rb30 (which i dont think you will need to)the same turbo can be used, and fry the tyres up to the legal speed limit with more response than you can poke a stick at. If you feel you must have more than 300rwkw, then bite the bullet and get a real gt35r, with a .82internal or you can get away with an external gate .63, but i believe on pump fuel the exhaust backpressure will limit the power to far less than the comp wheel is capable of making. We need something between a gt30 and gt35!

i find this topic interesting....

Just incase anyone cares...

my gt35 with .63 rear isn't as laggy as you'd originally expect.

3000rpm = 0.56bar 8psi

3500rpm = 0.82bar 12psi

4000rpm = 1.04bar 15psi

Once external gate is fitted should be fairly good.

Just hoping the .63 rear doesn't choke up the gt35 housing too much in the top end. For the conservative boost ill be using it shouldn't.

^^ thats fairly laggy IMO.

I had my GT30 .82 on by 4200rpm and was over 15psi and make more power than you will be able too :yucky:

500rpm to get that last 3psi once spooling is indicative of the large compressor side

after 4k the boost sky rockets but thats when i back off, yet to see what it does after that.

yea but at the end of the day, It's all about experimenting....gimme a break...i just spend 2k on this turbo, gotta stay positive hehe.

I'm not doin it to beat anyone else...doin if for my own thrills.

It's fairly laggy i know but off boost it drives great and doesn't break traction which is what i was after.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...