Jump to content
SAU Community

Lots Of Gtr Stuff - 17 X 9 Rims, Te37's, Dump Pipes, Manifolds, Tyres, Seats, N1 Turbos, Ecu's, Chip, Z32's, Greddy Oil Cooler, Nismo + Z32 Afm's,


Recommended Posts

Not really keen on swaps - but pm me with some pics anyway.

Heya,

Just wondering if you were willing to swap 18"s for the Te37s?

Bored to suit Tomei Pistons - Tight Clearance (2.2 ~ 2.5 thou) from memory.

The pistons are in another block now...

Will have it mic'd up for a serious buyer.

(I actually have just bought a set of 87 mm slugs so may even end up using it myself)

Tomei run a 1.9-2.2...bloody nice and tight eh...pics of the cusco front uppers please.

Will PM you with pics shortly.

Tomei run a 1.9-2.2...bloody nice and tight eh...pics of the cusco front uppers please.

Hi, do you have the nismo afm's still for sale. What is the difference between standard and nismo afm's.

Regards

76gtr

  • 2 weeks later...

OHLINS SOLD (still have HKS Springs and Cusco Tops)

GIAS SEATS SOLD (Plain ones still available)

ARC AIRBOX SOLD

N1 VENTS SOLD

  • 3 months later...

hey mate just wondering if you still had your hankook and advan tyres? if you do wahts the lowest price you would do for each pair or together? how much tread left?

thanks

jake.

  • 3 weeks later...

can you email pics of cusco upper front arms to [email protected]

do you know what the - rating of these are? or are they adjustable? and if so. how far?

email best form of contact as SAU doesn't work on my home computer... FML

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...