Jump to content
SAU Community

Recommended Posts

i hate

the bike cops that have a 3 way convo while cruising down north east rd in peak hour traffic, holding everyone up. :)

the fully hektic ulehs coming into gym with jeans and steel cap boots

acting all tough in front of the ladies, then lifting 5 reps of 20kg on the bench before they drop it >_<

god thats funny shit, but it still pisses me off!

/weekly sook.

  • Replies 452
  • Created
  • Last Reply

Top Posters In This Topic

police sitting on the expressway pulling over people after a hard days work that a % of that days wage goes to pay this dickhead officer and his mates sallaries.

get a f**kin life cops, dont worry bout the real crooks go get that revenue!

for the record i wasnt speeding and didnt get pulled over, but come on......there are hundreds of other things that this police officer could be preventing/solving/policing yet he wants to pull over the guy doing 5kmph over the limit on a f-ing freeway.......

police sitting on the expressway pulling over people after a hard days work that a % of that days wage goes to pay this dickhead officer and his mates sallaries.

get a f**kin life cops, dont worry bout the real crooks go get that revenue!

Yeah I see that quite a bit - they're on a bike, flopping out the radar to check the speed of the people either going down the hill or up the hill.

It's pathetic. It's on a hill!!

i hate when u go to the pub, find out some people dont like the group of people you are with so you have a talk and shake hands only for them to come back later when walking down the road and bottle your mate over the head and break his collabone (sp). :P

I hate...

-Cyclists who talk to each other and arnt in single file thus hogging road

-Old commoredores (the ones with loud droney exhaust and laggy auto boxes)

-The guy i saw the other day gatin' in a school zone

-The Novice by Glenda Millard (a book I was forced to read once)

-People that sit in Maccas carparks dosing for extended periods of time

-The RTA

-Monsta Mega Super Power T04e Turbo's for $300 (ebay)

-Old men that beep their electric scooter horns at you

-Surds

-Need for speed series (after) Underground 2

-Coke machines that ninja ur money

-old ladies that walk around with no bra

-supercheap auto catalogues cuz all pages seem to be about air compressors

-prison break season 4 cuz it has turned into like a cop show

-maccas drive thru cuz they takes like 10minutes to make a mcflurry

-public toilets (the toilet paper, and the fact that people think its cool to piss on the ground)

-Holden cuz they scab everyone elses stuff (chev engine, nissan engine)

-My guitar hero guitar cuz the red button is on drugs

-old ladies that press their heads against teh windscreen and drive half the speed limit and make eratic turns etc.

thats all I got for now

-

Edited by HKS_25T
i hate lining up at servo's and having to wait for 15minutes for the stupid prick behind the counter to slowly but surely serve 2 other people. Clearly unable to speak a word of english and has had no introductory on how to do his job efficiently.

We all speak English at my work..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...