Jump to content
SAU Community

At Wat Power Level Do U Start Running Into Problems With The Standard Rb26 Fuel Rail


Recommended Posts

  STR8E180 said:
i realli dont want to go threw all the trouble of fitting a surge tank and all the lines im after some thing i can just bolt in and fit the problem

i wanna get out of this the most cheapest way i can as well

On the cheap? Here's my suggestions to save coin;

1. Use stock pump and dont go for big power

2. 044 intank, tune for 380 or so rwkw and be happy with that power

im running a 044 intank, using a efi v8 falcon fuel sock retrofitted to suit the bottom of the 044.

simple install and no issues with 5 ltrs in the tank around corners etc.

only way to do it IMHO.

note the clear fuel hose i have mounted around the pump absorbs all the vibration, so its very quiet.

post-24852-1228029911_thumb.jpg

  STR8E180 said:
i had my car on the dyno for a tune yesterday and when we got to 400kw it started running into problems with fuel

we had a fuel pressure + flow gauge connect to the car while we were tuning the flow doesnt drop at all but the fuel pressure goes from 40psi to 60psi and then just drops back down to 40 instead of going higher it just drops back to 40 and the car leans out so we neva got to finish the tuning

fuel system is pretty basic

bosch 023 (rated at 700hp) mounted intake

SARD 800cc injectors

HKS fuel reg

Fuel pump for sure. Stock rail is good for well over 400awkw (maybe more, but ive had a few RB26 in here pull well over 400 with no issues)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...