Jump to content
SAU Community

Recommended Posts

RB30:

- Full set of Federal and Mogul cast pistons only, no rings - better than stock rb30e pistons.

to fit standard bore size - use standard rb30e piston rings.

$200

- Standard Rods + Pistons + Rings in good condition.

$50

RB25:

- Air con compressor

$150

- Short block - has pistons, crank and GTR rods bolted on only - good for rebuild:

$300

RB26:

- Standard pistons, came off R32 GTR with 89,000km - good condition

$100

R33 GTST:

- Custom turboback exhaust with changeable diff-back section to stock - mild steel - 2yrs old

$250

RANDOM:

5x 14x8 + 1x 14x9 wheels (i think) - bought these and they didnt fit on my skyline.

$200

Autogauge gauges - water temp, oil temp + oil pressure in bracket to fit into DIN pocket.

comes with all senders and sandwich plates needed - used

$80

I'll update the thread when i find more stuff in my garage.

Contact via PM.

Link to comment
https://www.sau.com.au/forums/topic/247292-rb30rb25rb26r33-gtst-parts/
Share on other sites

wouldnt happen to have some rb pickups u want to offload?

I'll check my garage but i doubt it mate.

all pm's replied.

guys, im a bit slack in getting pics up because of work bla bla...

the gauges are the smoke faced gauges from just jap that are black when they're off and light up when you turn the ignition on.

  • 2 weeks later...

UPDATE: found a boost controller to go with the kit - i will sell the entire kit for $100 with the 4 gauges + oil pressure plate/switch. i couldnt find the water or oil temp sensors anywhere. they go for around $30 for the water temp adapter from justjap and around $5-10 ea for the temp sensors.

pics up.

Note: stock rims in pic do not come with this set.

post-13452-1229316100_thumb.jpg post-13452-1229316108_thumb.jpg post-13452-1229316130_thumb.jpg post-13452-1229316153_thumb.jpg post-13452-1229316164_thumb.jpg post-13452-1229316178_thumb.jpg post-13452-1229316200_thumb.jpg

Edited by SECURITY
Where are you located? I need an air con commpressor.

im in bankstown. pm sent.

Can you tell the reason why those wheels didn't fit your car?

they dont clear my brakes. with spacers i think they'll fit, they are a skyline stud pattern though.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...