Jump to content
SAU Community

Recommended Posts

My v-spec ii has s-tune currently, the spring rates are front 6kg, rear 6.7kg,

there are 5 levels of hardness on the damper (I haven't tested them).

While I'd like a more compliant ride I don't think I want a harder ride ..

but is there anything to gain in the handling department without going harder?

Should I leave it alone? Add stuff from the nismo suspension catalog?

What about something ride height adjustable? getting into my garage is

a pain in the ass i have to take it 45 degrees and even then I'll get a scrape..

Link to comment
https://www.sau.com.au/forums/topic/248021-where-do-i-go-from-s-tune/
Share on other sites

I have Tein Monoflex, damper and height adjustable. They seem pretty good to me but I dont know how your ones go so cant compare them

according to a catalog they are front 9kg rear 8kg, so that would

be a bit harder than the s-tune ..

where in the "16 levels of adjustability" do you set yours?

what is it you don't like about the current handling? My point is it may not be the shocks. it could be alignment or a whole range of things. The S-tune gear is fairly good. since they use a circlip to retain the lower spring platform you could get the height changed if you want to raise it up a bit. but otherwise to improve handling I'd look at getting some adjustment so you can get a more performance oriented alignment (if that's what you want). start with some castor adjustment, front camber and then look at rear camber too. that will be a good start before binning your shocks and starting again with new ones.

what is it you don't like about the current handling? My point is it may not be the shocks. it could be alignment or a whole range of things. The S-tune gear is fairly good. since they use a circlip to retain the lower spring platform you could get the height changed if you want to raise it up a bit. but otherwise to improve handling I'd look at getting some adjustment so you can get a more performance oriented alignment (if that's what you want). start with some castor adjustment, front camber and then look at rear camber too. that will be a good start before binning your shocks and starting again with new ones.

thanks, you are right I am putting cart before horse.

I need to spend more time with the setup before deciding what to do..

my main issue so far is that the setup doesn't feel like it will be the master of either

compliance on the roads, or master of track either. So I ASSumed it was comprehensively

outclassed by the coilovers commonly used now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...