Jump to content
SAU Community

Recommended Posts

R5 - Phillcom Rally Time Attack Round 2 October 5th

NOW OPEN - Expression of Interest

I'll be down for the Time Attack again :happy: hopefully the weather will be a bit cooler so i can run full boost for the whole day unlike last time.

Congratulations to Douglas Lehmann (Open Modified) and Corey Armstrong (Club Cars) for winning the AWD Turbo Challenge Round 4. The SCCSA Wintercup 2 Collingrove Hillclimb was again damp early with near perfect conditions for the afternoon runs. Great to see so many competitors recording personal bests! The leader board is starting to look a little more interesting with only 3 rounds to go!

  • 2 weeks later...
  • 1 month later...

Congratulations to Steve Knight (Open Modified) and Corey Armstrong (Club Cars) for winning the AWD Turbo Challenge Round 5 - Phillcom Rally Time Attack Round 2. Both drivers recording personal bests in near perfect conditions.

Two rounds remaining in this years AWD Turbo Challenge, and the top 9 drivers in Open Modified Class are separated by only 5 points! What a ripper way to lead into the SA Hillclimb Championships Collingrove and Pirtek Legend of the Lakes Hillclimb Mt Gambier!

  • 2 weeks later...

Congratulations to Douglas Lehmann (Open Modified) and Michael Willis (Club Cars) for winning the AWD Turbo Challenge Round 6 - Peter Lehmann SA Hillclimb Championships. The final AWD Turbo Challenge round is less than three weeks away, and the series end WILL come down to the final run at the Pirtek Legend of the Lakes Hillclimb Mt Gambier!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...