Jump to content
SAU Community

Recommended Posts

Had a run in with a very sturdy post :D

What is it with these sturdy posts, they're everywhere!

post-56452-1229450305_thumb.jpg

...and don't get me started on those concrete walls! :):thumbsup:

post-56452-1229450580_thumb.jpg

...eeech, I just realised how dirty my wheels were. I think I might need to go get a wash myself.

Edited by mr_infamy
Had a run in with a very sturdy post yesterday whilst reversing out of the car wash place. Yes it was after I washed the car and dried it. Yes I have insurance. Yes, I'm an idiot.

Just thought I'd share. :)

a combination of bad luck, inattention and concentration loss; we've all done it. of course, this doesn't make it any easier. don't you hate that "crunching " sound, even before you inspect the damage, you know it is going to cost $$$. no, you are not an idiot, but we all feel pretty stupid after an incident like this. I know I did!!!. the good part of your story is that nobody was injured. good luck with the upcoming repairs.

a combination of bad luck, inattention and concentration loss; we've all done it. of course, this doesn't make it any easier. don't you hate that "crunching " sound, even before you inspect the damage, you know it is going to cost $$. no, you are not an idiot, but we all feel pretty stupid after an incident like this. I know I did!!!. the good part of your story is that nobody was injured. good luck with the upcoming repairs.

Thanks. This is only the 2nd bingle i've had since driving in my entire life so i suppose i should count myself lucky.

Thanks. This is only the 2nd bingle i've had since driving in my entire life so i suppose i should count myself lucky.

+1 for the R34 front end conversion.

When will these be available locally from a supplier in Australia at a reasonable cost? MASA Copies?

I did see some aftermarket front guards (vented I think) available on Ebay (Australia) a couple of weeks ago.

Well, the body panel shop had a look at the damage yesterday, looks like i'll definitely be going through my insurance company. He (body panel guy) said i'll need a new front bar and right guard. I've told him it's a Dayz front bar. Should I leave it to him to source the parts or steer him in the right direction? Any recommendations? Oh yeah, and I should be able to keep the old Dayz front bar... :banana:

When will these be available locally from a supplier in Australia at a reasonable cost? MASA Copies?

They are available now, just not well advertised

Steer the panel shop in the right direct, otherwise the insurance company will get the cheapest option they can.

Your Dayz front bar should have a part number moulded in the back of it. make sure the quote includes the right parts.

If you get to keep your old front bar, get a mould made of it and do all the sad series 2 owners a favour.

Talk to CCubed (andrew) about getting a mould made or a R34 kit if you are interested.

In my drive, which is angled up hill from the property, on the nature strip I installed a really neat solar (God I am an enviromentalist and didn't know it)

light, and the bloody Postman farked it while reversing out after delivering a new bit for the S1.

It happens.

After speaking to insurance assessor and panel beater, I'm going to get a new Dayz front bar (they couldn't find a 2nd hand one anywhere) and panel jobbie fixed in Jan 09 so all's well. Apart from having to pay my excess ofcourse. I've told him i want the front bar back too. :banana:

I wonder where he's ordering the new bar from? Wasn't aware they still made them.

Hugh.. sheesh, you're not having much luck with the S1 are you?

Edited by webng

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...