Jump to content
SAU Community

To wang, or not to wang.... that is the question?

Cyric

By Cyric,
in Victoria

 Share

Recommended Posts

Cyric Collaborator

Cyric

Posted
Posted

OK so you've all seen my jiant wang, and told me its too big (but i'm used to that )... So I ordered a stealth wing...

Now everybody says keep the wang.... make up ur dam minds ppl!!!

Here are some pics of the stealth wing, let me know

http://coppermine.e-clips.com.au/thumbnail...ils.php?album=4

And for those of you who havent seen my wang yet, here is a shot of that as well http://coppermine.e-clips.com.au/displayim...p?album=2&pos=2

Cyric Collaborator

Cyric

Posted
  • Author
Posted

yeah im up for that :) we havent had a meet for awhile anyhoo, gunna turn it into a coffee table if it come off... although the wang is ahead on votes at the moment, which is a bit of a concern... it is however way behind on exculsive so i might have to add them together, or do some sort of magic mathamatics so the wing comes out victorious, im with every1 else, the wang is rediclous...

Originally posted by SLYWPN

Why dont we organise a SAU BBQ and use your wing as the picnic bench? :)

Al Grand Master

Al

Posted
Posted

I have liked the stealth wing for the past 2 yrs, I just prefer to spend my money on power modes rather than cosmetics :).

Ps: Have recently invested money in property, so the turbo/engine upgrade has been put on hold :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB26 swapped gtst

      By GTSBoy · Posted

      Just get rid of the orignal low impedance injectors, replace with modern high impedance injectors, and you won't need the resistors. Wire direct, as per any other engine.
    • GTSBoy
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By GTSBoy · Posted

      Tao, we're not talking about the ECU boost ref. We're talking about the wastegate signal source.
    • GTSBoy
      Belt flex under throttle

      By GTSBoy · Posted

      Flapping up and down is a consequence of the varying pull on the belt. When the engine speed is suddenly increased, the tension in the belt increases too. When that engine accel changes to decel, the tension is reduced and turns up as a little extra length of beltes between the pulling and dragging pulleys. That extra length flaps up, then down. There's all sorts of other harmonic stuff going on too.
    • r33.antwone
      RB26 swapped gtst

      By r33.antwone · Posted

      hello ladies and gentlemen so i’ve swapped a rb26dett into my r33 gtst and ive come across many speed bumps but its nearly over what im having issues with is the injector resistor box that are normally on the RB26 fuse box but im still using my rb25 fuse box and as a result my injectors aren’t getting power and is the last thing i need to figure out so the car can start. can anyone help me out on where i can find a wiring diagram for the rb26 harness to see where the injectors are supposed to receive power 
    • hypergear
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By hypergear · Posted

      The boost pressure at the compressor cover will be higher than at inlet manifold. lets say, trying to hold 20 psi flat at 7000 RPM. If your wastegate opens at 20 psi measured at the compressor cover, the engine may only be seeing 16 psi. Your base pressure reading at engine would be 20psi by 4K and 16psi by 7K while your MAP at compressor housing still reads 20psi at 7K. For this reason your ECU's MAP source is never on the compressor cover. This difference isn't a major concern if you're using an electronic boost controller (EBC).
×
×
  • Create New...