Jump to content
SAU Community

Recommended Posts

Hey everyone,

Myself and a Mate (astrotristan) are currently looking for the following parts, to suit R32 of course.

1 - Dash (no rips or bubbles) inc. Airvents (mainly left side) and Glovebox

2 - Complete Center Console

3 - Dash Surround

4 - Rear right taillight Cover (the plastic part that surrounds the taillight, dont care what colour, no damage)

5 - GTR bonnet (dont care what colour or paint condition, no damage and heatshield intact)

6 - GTR Grill (dont care what colour or paint condition, no damage)

7 - Plastic trim, under the steering wheel above pedals (dont need vent, good condition no holes)

8 - Dash window vents (no sun perish or cracks)

9 - 4 x Stock R32 Rims (tyre condition no issue)

Im sure there is more, we will come to require over time.

Even if you do not have these parts, if you have come accross them in your travels let us know whats around.

Cheers,

D

Link to comment
https://www.sau.com.au/forums/topic/251968-wtb-r32-parts-body-interior-etc/
Share on other sites

PM'd thoese with parts on offer.

Also require...

- GTR bonnet (dont care what colour or paint condition, no damage and heatshield intact)

- GTR bonnet L latch

- GTR Grill (dont care what colour or paint condition, no damage)

- HKS super dragger / silent hiflow 3" catback exhaust ( or similar, want somthing 3" and reasonably quiet)

- Need 3" cat too, if your including with exhaust sweet.

- Front / Rear Strut Bars (pref same brand / pair)

- door cards would be good, or the frp ones, if somone wants to trade stockos (poor condition) + cash im keen for frp.

- passenger airvent

- need a pair of 17 x 8 stocko under 100bux, dont care tire condition.

- type m side skirts (dont care what colour or paint condition, no damage)

- standard r32 rear bar, with mounts (dont care what colour or paint condition, no damage)

- reverse lights

- under bonnet rubbers

there is heaps of shit i need, so let us know.

cheers



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...