Jump to content
SAU Community

Recommended Posts

I am currently doing up my project car a 1981 Ford Laser and doing a full respray job on it , doing the car up to be a show car and possibly entering the car in summernats in years to come...

Looking at where to buy Midnight purple paint from ... if anyone has paintcodes for it or if I can get it direct from nissan ?

Anyone got any ideas on where to buy around 4 litres from ?

Link to comment
https://www.sau.com.au/forums/topic/251982-midnight-purple-paint/
Share on other sites

You will need the paintcode for it.

BNR32

* KH2 - Gun Grey Metallic

* KG1 - Jet Silver Metallic

* TH1 - Dark Blue Pearl

* AH3 - Read Pearl Metallic

* 732 - Black Pearl Metallic

* 326 - Cristal White

* KL0 - Spark Silver Metallic

* BL0 - Greyish Blue Pearl (special order)

* AN0 - Wine Red

BCNR33

* AN0 - Super Clear Red

* BN6 - Deep Marine Blue

* KH3 - Black

* KL0 - Spark Silver

* KN6 - Dark Grey Pearl

* LP2 - Midnight Purple

* QM1 - White

* BT2 - Champion Blue

* KR4 - Sonic Silver (Post 1996)

* AR1 - Super Clear Red II

BNR34

* TV2 - Bayside Blue

* QM1 - White

* KR4 - Sonic Silver

* KV2 - Athlete Silver

* GV1 - Black Pearl

* AR2 - Active Red

* EV1 - Lightning Yellow

* LV4 - Midnight Purple II

* LX0 - Midnight Purple III

* WV2 - Sparkling Silver

* QX1 - White Pearl

* EY0 - Silica Breath

* JW0 - Millennium Jade

Not 100% sure if these are the same in Australia as I lifted them for a maylasian skyline club page: Source but I thing National Capital motors in Tuggers (I think that who it is) are good with paint code translations.

Only problem now is which midnight purple ><

Edited by Helious

I bought another ltr of lp2 midight purple yesterday from our local piant supplier to finish my engine bay. Just take them in the paint code and tell them how much you need. There should be no drama and takes about 10 minutes. You can only get LP2 in base coat though. So you'll obviously need clear coat to.

Edited by Evocoop

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...