Jump to content
SAU Community

Recommended Posts

i have four 18inch axis rims in good order no scratches and dints the tires are worn out. this picture is off tempetires ill get the propper photos later.700 bucks

post-25975-1231930093_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/252580-18inch-axis-rims-and-tires/
Share on other sites

how worn out r tyres?

i have four 18inch axis rims in good order no scratches and dints the tires are worn out. this picture is off tempetires ill get the propper photos later.700 bucks
Edited by restless

i cant remember how wide the rims are i think they were 9.5 inches the rear tires are 255 and 225 on the front so that should help on the width,they were pretty worn out on the rears, on the inside of the rear tire there was pretty much no tread left and the front had a little bit of tread left but all of them would have to be replaced so ur not getting harrased by the police. my last set of nankans were 190 each.

they fitted on my r32 gtst skyline with series 2 brakes they would fit 32, 33 and 34 skylines and other cars but not sure

sorry located in orange can organise to meet halfway if buyer lives in sydney or organise delivery here's a pic of them on my car ill have prob pics on saterday

sorry located in orange can organise to meet halfway if buyer lives in sydney or organise delivery here's a pic of them on my car ill have prob pics on saterday

post-25975-1232018461_thumb.jpg

the 225 are alright but the 255 are pretty much f!@#$d as u will c in the pics but the rims are good if any1 is interested please ring my mobile 0419284730

thanks brad

post-25975-1232434372_thumb.jpg

post-25975-1232434459_thumb.jpg

post-25975-1232434547_thumb.jpg

post-25975-1232434611_thumb.jpg

post-25975-1232434669_thumb.jpg

post-25975-1232434723_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...