Jump to content
SAU Community

Recommended Posts

Hey all, just a little confused and looking for a little assistance in regards to the front torque gauge.

I know that the AWD is working however the gauge does not do anything it just sits on 0

I was just wondering if there is an individual fuse for it or anything special like that. I just wanted to see if anyone can direct me rather than just attack it blindly lol

Cheers guys

Link to comment
https://www.sau.com.au/forums/topic/252648-front-torque-gauge/
Share on other sites

Drop the clutch from a standing start.

If the rears just smoke. Its the whole system thats not working.

If bogs down and pulls but the gauge dont move. Its the gauge.

If it bogs down, pulls and gauge begin to dance - She's a goer.

ATTESSA fuses are located in the kick pannel on the right of th steering wheel and in the engine bay drivers side.

Drop the clutch from a standing start.

If the rears just smoke. Its the whole system thats not working.

If bogs down and pulls but the gauge dont move. Its the gauge.

If it bogs down, pulls and gauge begin to dance - She's a goer.

ATTESSA fuses are located in the kick pannel on the right of th steering wheel and in the engine bay drivers side.

Yea i have tested it out and i can tell the AWD is working, went out lastnite to check lol and it was gripping (in the rain) so i might check the fuses as it'd be nice to see that metre working as the other oil temp and boost obviously work fine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...