Jump to content
SAU Community

[question] I Have Just Installed A Split Dump Pipe, And My Engine Bay Seems To Be Running Hotter Than Usual


Recommended Posts

Hi all,

My apologies if this has already been posted, but i failed to find it in a search.

I've just had a split dump pipe (Flying Performance) installed today by my dad (thanks dad!) and myself.

One thing that seems mildly concerning is it seems as though after a 45 minute drive, the engine bay is hotter than usual- particularly the area close to the turbo.

I've got a Series 2 R33 GTS-T. The only other mods are the $22 boost controller (dialed in at approx 9 PSI), Catco 3" hi-flow cat (came with car), 3" catback exhaust.

It doesn't appear that any coolant levels have dropped, and performance is fantastic (much smoother power delivery and rev's)- i'm just concerned about the temperature.

The stock temperature guage didn't go any higher than just about the middle.

Any help would be appreciated!

Thanks!

its probs a thinner material and/or not as good at holding the heat in compared to the standard steel ones, therefore will let out more heat...

its probs a thinner material and/or not as good at holding the heat in compared to the standard steel ones, therefore will let out more heat...

spot on

Thanks guys- will do!

I probably won't get a chance till next weekend, so just in the meantime- is running it as it is now detrimental or unsafe? Either for the car, performance or the engine?

Thanks guys- will do!

I probably won't get a chance till next weekend, so just in the meantime- is running it as it is now detrimental or unsafe? Either for the car, performance or the engine?

Quite fine to run it like that mate, i was running a s/s manifold and dump off my s15 a while ago for over a year.

Heat wrap is the best idea but you already put the pipe on so would be a bit of a bugger to remove it again but ohhhh well, you gotta do what you gotta do!

???? keeping more heat in with wrap may increase the chance of s/s cracking; especially with poor quality welding and grade.

Anyone have experience with this?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
×
×
  • Create New...