Jump to content
SAU Community

Recommended Posts

hey guys its time to sell my car, awesome car making 330kws easily alot more is able to be made but we were limited as dyno cell was 40+degrees

MAKE: Nissan skyline 1995 r33gtst with rb30/25det non vct

11months rego

ENGINE: tomei cams 10.2 lift

mahl pistons

acl race series bearings

argo rods

cometic head gasket

garret gt3540 with .82 rear

hks intercooler

3 inch exhuast with titanuim tipped cannon

rpm technoligies spring sprung ceramic button clutch

side facing plenum

sard 770cc injectors

bosch 044 in custom surge tank mounted in boot

spit fire coil packs

z32airflow meter

apexi power fc and hand controller

eboost 2

adjustiable cam gears on inlet and exhuast

EXTERIOR:

18x9 ruff rims with new tyres on rear front tyres ok, tyres replaced on rear cause dyno chewed them out

greddy coilovers

hicas removed and lock bar is in place

new inner tie rod ends

PRICE 18,000 ono or may swap for something of my interest

post-33568-1233038347_thumb.jpg

post-33568-1233039223_thumb.jpg

post-33568-1233039413_thumb.jpg

post-33568-1233042362_thumb.jpg

post-33568-1233042377_thumb.jpg

Edited by stocko

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...