Jump to content
SAU Community

Recommended Posts

Hey Guys,

I've upgraded to a MoTeC M800 with all the fruit for the RB30/26 and I never got to use my R32/R33 GTR Power FC. This is a Personal Sale of my own good and not drift shop.

Specs:

R32 / R33 GTR Power FC (All R32 and R33 GTRs)

Model Serial Number: PFC GTR33L 020-1605 MADE IN JAPAN.

I bought it for $1650 a while back for my RB30/26 conversion, but I've now bought a MoTeC M800 to run all of my cars instead of having 3 Different ECUs. The beauty of the MoTeC is that you can change the engine config via the software to suit 4/6/8/etc within 60 seconds. Since I can only drive one car at once, - it made sense to have the best ECU and swap it out between each car.

Your price: $1199 Delivered.

Pics:

IMG_3705.jpg

IMG_3707.jpg

IMG_3719.jpg

Item is packed in the original Apexi Box.

Bank: Commonwealth Bank Australia

Name: Costa Tsimiklis

BSB: 063106

Account: 10280429

Amount: $1199 Delivered

Please use your SURNAME as a payment description, or your postcode if you can only enter numbers.

Please advise me of the following details...

Transfer Receipt:

Full Name:

Delivery Address:

Phone Number:

Email Address:

Cheers!

--

-----

Costa

Drift Shop Australia

www.driftshop.com.au

[email protected]

Will be on ebay at $1250 if it does not sell by the end of this week. I would prefer to sell it to a fellow SAU member :banana:

  • 2 weeks later...

Going up on eBay as a buy it now. I will honor this price at $1199 delivered unless someone buys it on eBay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...