Jump to content
SAU Community

Recommended Posts

Is it for S1 or S2 R33?

how do i tell...PaulR33 ??

EDIT: just found out it doesn't matter...but as its a brand newie id say its for a series 2. But either will work in either.

Edited by DiRTgarage
how do i tell...PaulR33 ??

EDIT: just found out it doesn't matter...but as its a brand newie id say its for a series 2. But either will work in either.

Yes, will work in both series 1 and 2

Look all the wankers PMing with low-ball offers...its this simple...

THIS IS A GENUINE AUSTRALIAN PRODUCT FROM ACCESS AUTOWORKS...NOT A CHEAP IMPORT AND IS ALMOST $500 LESS THAN COST !!! HOW MUCH MORE OF A DISCOUNT DO YOU THINK YOU ARE COMFORTABLE RIPPING OUT OF MY WALLET?

COMES WITH FULL SUPPORT AND PART WARANTY.

see look...

http://www.accessauto.com.au/Items/ap-414-...GTS-T%20RB25DET

They are $2200 from Greenline and are no longer available from Nengun...$1500 is an absolute bargain.

Edited by DiRTgarage
cheap power fc's are a thing of the past since our $ went up to shit.

Unfortunately everyone now wants a Vi-PEC...making the Power FC even harder to sell.

Might have too keep it and show my grankids what we used to put in our cars...they will say "omg solid state technology used to run your cars...gee grandad you are old"

Edited by DiRTgarage
Look all the wankers PMing with low-ball offers...its this simple...

im pretty sure i sent you a pm asking if u can send to adelaide, and at the same time asked for bank account details so i could put in the full amount you were asking in!!!!

you had your sale right there... you lost your sale right here, i dont think i will buying from you now

i dont intend on being a keyboard warrior :D but your sale tactics fail

im pretty sure i sent you a pm asking if u can send to adelaide, and at the same time asked for bank account details so i could put in the full amount you were asking in!!!!

you had your sale right there... you lost your sale right here, i dont think i will buying from you now

i dont intend on being a keyboard warrior :D but your sale tactics fail

You actually said this...

ok, let me do a bit more research into it. as it'll be going into R32 rb25det there's a few thing im unsure of.

to be fair i thought id wait till i heard "yes i definately want it from you" before forwarding any of my details.

If you thought i was putting you in with all the "ill give you $800-$1200" people you were wrong, very wrong. You were one of the only people trying not to squeeze as much off it as you could...much appreciated trading. But getting my PM box hammered everyday by low ballers is a little frustrating.

no big deal...no 'sale tactics' here mate...ill put it on the shelf till someone genuine comes along.

Edited by DiRTgarage

Hey there

Just tryed sending a message but ur inbox is full. I am very interested, i have a local source stating a similar price i believe which i am checking tommorow. I really am after one without the hand controller but if i cant find anything tommorow then I shall shall send a confirmation either tommorow night or tuesday morning, unless you sell it before then of course. But key me in for definately interested (And not argueing on price :D ).

Cheers. Luke

hey mate sent you a pm the other day about the z32 afm, havent got a reply from you but basically im just wondering if you still have it and if it comes with a plug too coz im keen to take it off your hands

cheers dale

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...