Jump to content
SAU Community

Recommended Posts

this may be a very silly question but i am going to ask away any ways.... when is it time to get a engine rebuild or a new motor all together like how many kms? down the road my R34 is pushing 264,000 kms Dam that Melbourne trip and back to Perth from Geraldton was fun........ haha :D

I just put in New Spark Plugs and coil pack and my nasty Busted WRX Sounding motor is sounding way better now and not a WARNING light to be seen :):P:cool::D:geek:

So the question is how many kms before a new motor is needed?

Edited by DiNoBoNeS
Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/
Share on other sites

until it dies

depends how its been looked after

better = longer

no real number, lots of taxis run around with 600,000kms+

but they leave there cars on all the time and service very often

Tops thanks mate i try and look after her and do the right things i work as a photographer and i leave it running when i am shooting I am only with the guy/gal for like 4 minutes so no need to turn it off and on all the dam time... just was thinking if there was a kms number to do it or if it was the case of wait to it go hehe she is running strong and i do not think it will be for a while i can not wait for 300,000kms.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400195
Share on other sites

when it gets low compression, or has a fair bit of leakage.

leaving a car idling is not ideal either, the fuel isn't burnt correctly, and runs down the side of the bore, washing off the oil with it, and contaminating the oil.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400198
Share on other sites

your car will get hot if its just sitting there idling

best to just let it run for a minute or 2 then turn it off

rebuild it when it pops...

your car gets hot just idleing?

i dare say keeping it running > on and off all the time

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400429
Share on other sites

your car gets hot just idleing?

i dare say keeping it running > on and off all the time

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400446
Share on other sites

yep.. the only time we realised we hadn't plugged my mates thermo fans back in, was when we pulled into the macca's drive though, and it started to get hot.

most fans will stop, or slow down when the car is moving.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400449
Share on other sites

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

That's pretty hot dude.. highest I've ever seen on my 30 is 104deg and that was after a couple of big smokey burnouts on a 40deg day!

FYI boiling point is around 110-115deg.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400565
Share on other sites

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

If your car is getting hotter when its idling then something is stuffed. When temps start to rise a bit the fan is suppose to kick in to pull air through and keep temps steady.

My temps don't rise one bit no matter if I'm moving or not. Sits on 73 deg all the time (PFC hand controller and new watter temp sensor). Car also runs an N1 watter pump which doesn't flow as much watter at idle as a normal watter pump and still no issues at all

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400819
Share on other sites

95% of engine wear happens when the engine is cold. Thats why taxis engines start to go at 1,000,000kms, and trucks get their engines rebuilt when they clock back to 0 only because they can. I've worked on trucks with over 500,000kms with engines that are fine, and cars that have bearing noise at just over 200,00kms.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4401253
Share on other sites

If your car is getting hotter when its idling then something is stuffed. When temps start to rise a bit the fan is suppose to kick in to pull air through and keep temps steady.

thats only if you have thermo fans on your car

belt driven fans are constantly working and engine temp SHOULD co up slightly if not moving due to less air movement through the core

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4402123
Share on other sites

(feel free to correct me people)

Oil is a major factor in engine wear.

your engine would run dry for 2 seconds before the cold oil is pumped up to the valves and while the oil is cold its not flowing easily.

I've seen inventions for pre-heating oil sumps before starting, and i'm sure someone will have invented a oil primer.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4403775
Share on other sites

actually the fans on RB's are clutched, they apparently stop moving at higher speeds.

but yes, they are constantly spinning at idle

They don't stop spinning at high rpm, the clutch is there so that the fan isn't spinning at full engine speed at high rpm.

As for oiling, there are products out there that retain oil pressure in a container so that the instant you flick the key, it squirts the pressurised oil through the system immediately prior to startup.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4404321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...