Jump to content
SAU Community

Recommended Posts

Hi guys,

I did search on this and came up empty... I always seem to have that result though.

If anyone has any ideas it would be greatly appreciated :

Today drove the car about 20 k's to a friends house, half way there I noticed my oil temperature was really high, all other vitals are fine engine temp, oil pressure and so on, the car is running completely stock and has been running with out problems.

Oil levels are good too, I have teh stock setup with the water to oil cooler off the block no seperate radiator out the front but that has never been a problem, also this was before it got really hot today, just nice and early.

Has anyone seen this before?

Cheers,

H

Link to comment
https://www.sau.com.au/forums/topic/255051-really-high-poil-temp-help/
Share on other sites

i dont know about your car but my r33 has oil temp indicator on the dash cluster aswell as my own oil temp that i installed seperate. Did you notice the dash cluster go up aswell??? most likely its the temp gauge mistake, or were you drifting it to your mates place for 20km lol

Well my gauges are all in the center of my dash, factory gtr ones. So no aditional guages but mine has never read wrong before. Also was only costing along behind traffic so I wasn't even giving it a hard time.

So I still have no idea but I don't want to even drive it home tip I have some theories :sick:

Any other ideas?

mate, I have just had the same thing happen only with an Apexi oil temp running through an Apexi controller, I was driving along and all of a sudden after less than 5 minutes (so probably impossible for oil to get that high) the Apexi is reading 130 degrees, the warn light is buzzing away but the dash oil temp is not even reading yet (as is normally the case it takes about 10 minutes to get to temp).

All other temps pressures etc are fine.

Turned out to be a dodgy earth on the sensor. Probably just that on yours but pays to get it checked out asap. At 140 degrees if you stopped and took off the oil filler cap, she's be smoking

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...