Jump to content
SAU Community

Recommended Posts

Description:

Body:

Jett Black

Vertex Rear Bar

GP Sports Front Bar

GP Sports Side Skirts

M-sport Door Panels

M-sport 50mm Wide Rear Guards

ISC Performance 25mm Wide Front Guards

Rolling:

R33 4 Pot Calipers & Machined Rotors

5 Stud Hubs

S14 Rear Hubs

S14 Rear Calipers & New Rotors

Rays Wheels Nuts

Worx Miester S1's 18 by 10 + 22 rear

18 by 9.5 + 10 front

NPG Adjustable Coil overs / Cambertops (asnew)

Interior:

Short Shifter

Just Jap Gear Knob

R32 GTR Front Seats

Gktech Steering Wheel

Standard Remaining Interior

Engine & Gearbox:

Ca18Det Engine (good health)

S15 T28 turbo

Motule Oil

RB20 Throttle Body

RX7 550cc injectors

Jap Stainless Manifold

Advance Dump Pipe

Bosche Hec 716 Coils

Hurricane 8mm Leads

Boshe LM2 4 wire oxy Senson

Xtreme Clutch Plate

Exedy Preasure Plate

EMS Stinger 4424 ECU

EMS 4 coil ignitor Module

Custom Alum Intercooler Pipes

600 by 75 by 450 cooler (unsure on brand but works well)

Stainless 3inch mandrell bent exhaust

Highflow cat convertor

Alum Radiator

14inch Thermo Fan

Wahlbro 500hp fuel Pump (original)

Turbosmart dualstage boost controller

Car has not been tuned yet but runs fine on the current tune, SHould make around 180+ rwkws on 15 psi, Car is a real head turner, have been asked a few times about getting pictures done for magazines Spent thousands must sell for house reno's...

Call Todd on 0400032565 no reg or roadworthy

$12500

colac_090117_073b.jpg

colac_090117_074b.jpg

colac_090117_075b.jpg

DSC00184.jpg

l_e4e84f451f61014fec65da8b8d6ae39c.jpg

DSC02401.jpg

DSC02396.jpg

P8300056.jpg

Edited by SLK-GTR
Link to comment
https://www.sau.com.au/forums/topic/255222-custom-widebody-s13/
Share on other sites

DAMNNNNNNNNNN i've never been a fan of S13 but this one is an exception!

a few questions,

what year?

how many Kms on the engine and on the car?

what needs to be done to get RWC ?

any pics of interior?

thanks,

Hey mates its a 92 model it was non turbo sr20 auto the car had done 120thou kms i did the engine conversion my self everything was done properly and no corners were cut, the engine has done 80thou (what im told from the guy who i purchased is from) seems to be in good health no knocks doesnt burn oil etc, wouldnt need to much for roady as all the brakes, suspention and tires are new it wuld need a numberplate light connected maybe a rac boot on the drivers side and the suspention raised up obviuosly lol!!! i have some GTST r32 wheels that cme with the car they lso have new tires, these will be fitted to the car to get a roadworthy....

P2030008.jpg

P2030010.jpg

P2030011.jpg

P2030013.jpg

P2030015.jpg

P2030018.jpg

P2030017.jpg

P2030020.jpg

P2030024.jpg

P2030025.jpg

P2030026.jpg

P2030027.jpg

P2030028.jpg

  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hot tip, stop picking at shit. Live in bliss instead   From my recent experience in rust repairs, white it may seem to not go much further back, you'll still need to cut back a bit further.  From what I can see there, the outer skin, and the inner is rusted too. From what I can see you've got the inner one which is all structural, and window likely affixes too.   If tag Murray Calavera here, but my phone won't let me tag him, he'd probably be able to give the best advise.   I do know, welding roof panels is a right pain in the bollocks! Very heavy to heat distort the roof and warp it all.
    • Some of the filler.   Also if I look under the top flap of metal it starts looking good quite close to the edge. I get the feeling it doesn't go much further.
    • So, I finally started digging at the bit of my roof that was cracking and bulging a bit. Well, it was just thick filler that was covering some pretty bad rust. I didn't find the edges, I was too bummed to keep going.  There are a few holes as you can see. There was just so much filler but looks like no attempt under the filler to prime or use rust converter, just slapped filler on exposed rust.  Anyway, I'm going to take the windshield out and find the edges. I'd love to fix this myself as I'm pretty sure it'll be expensive to get done properly. I was thinking I could just get a cut piece from another E39 and just weld it in place as it would be the right size and shape.  Thoughts?
    • This is the territory of the "Stage 1/2/3 Golf GTI/R" or otherwise off the shelf tune with (relative to before) minor mods. It's easier now. Downpipe and Tune and boom, big increases. Stage 1 OEM+ is where it's at. This is where the niche evolved into and it's really easy to see why. It's rare to even NEED to consider changing turbos or going to aftermarket ECU's or building bottom ends for more power. Stage 1-2-3 will get you a LONG WAY. Civic Type R turbo GR Yaris/Corolla Anything with B58 (MKV Supra/x40i) Anything BMW in General Anything Audi in General Any turbo AMG RenaultSport Turbo offerings Korean Elantra N/I30N Ecoboost Mustangs Focus RS? List goes on. I would argue in the future it won't even need to go on... M3P is pretty rapid out of the box...
    • There is a way, but it's not with the same cars. You need to find the same vintage of car, that we had. Realistically, that was an affordable car with aftermarket parts around. So what people need to find is a car that had a decent base in its day, and can be modified. They're looking for a car year make of 2010 to 2015 really... Aus could have done it if Holden didn't fold as V8 commodores were cheap, and if Ford didn't get expensive thanks to COVID, then you could cheaply play with FG Barras. Realistically, those are just a bit heavier, four door skylines. I'm sure the US and UK have similar cars they could find.
×
×
  • Create New...