Jump to content
SAU Community

R33 Skyline Parts

skymugs
 Share

Recommended Posts

skymugs Collaborator

skymugs

Posted
Posted

hey im having a cleanup and sellin all the stuff i dont need. if you interested send me a pm or give me a call 0406751986... some parts negoitiable.. everything is available to pic up or post at buyers expense

RB25 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange used 3000k's $100

RB30 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange.comes withs gaskets. new and never used $150

Coilpack wiring $20

Ignighter box $30

38mm wastegate $50

RB25 dump $20 3 avail

Exaust manifold $30 2 Avail

Ignition Barrel with genuine key $30

inter cooler piping for front mout stainless. $20

Injectors in rail.. only 5 injectors. cant find the other atm.. injectors require clean because they been sitting aeound a while. $50

Throttle body s1 and s2 $40 each

s2 tps $30

Coil packs s1 $70

intercooler pipe with adapter for blitz blowoff valve. it can replace the standard pipe in that position $30

Gredy boost Gauge $30

Genuine oil filter $10

tomie 1.2 oil restrictors x2 $15 each

Standard intake pipe with blow off valve... one with out $30 each

cam gear cover $10

Oil cooler adapter with fittings $40

300zx oilcooler $10

genuine injector to manifold seals $10

Genuine rb25 headgasket 87mm bore $50

RB25 requires rebuild. belt came of at idle and broke 2 valves in cylinder 1. had 130000 ks, run fine before that, will come with good cams as it has been sitting around for a while and the lobes are pitted. comes with oil pump and harmonic balancer, $200

flywheel will need machining $20

Genuine inlet manifold gasket where it splits $30

charcoal canister $20

Washer Bottle with motors $30

wiper motor $30

coilpack cover $20

Maroon r33 wing make an offer... also have rear bumper

r33 dash make an offer.. welcome to come inspect

silicon right angle 2.5 inch bend $20

right angle fitting in pic (not speed flow) $10

Heat shields for manifold and turbo make an offer

complete inlet manifold with injectors, sensors, idle controll valve ect.. $200

top half of manifold x2 good for changing to a forward facing plenum $40 each

bottom part of manifold $10 requires new coolant outlet

plenum chamber $20

ALternator.. has been tested $70

power steer pump $50

standard turbo to airfilter pipe with adapter and k & n airfilter requires clean $30

some standard intake pipes in the pictures if you interested let me know and make an offer

please check the link for pictures http://www.boostcruising.com/forums/index....howtopic=384000

Link to comment
https://www.sau.com.au/forums/topic/255741-r33-skyline-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...