Jump to content
SAU Community

R33 Skyline Parts

skymugs
 Share

Recommended Posts

skymugs Collaborator

skymugs

Posted
Posted

hey im having a cleanup and sellin all the stuff i dont need. if you interested send me a pm or give me a call 0406751986... some parts negoitiable.. everything is available to pic up or post at buyers expense

RB25 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange used 3000k's $100

RB30 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange.comes withs gaskets. new and never used $150

Coilpack wiring $20

Ignighter box $30

38mm wastegate $50

RB25 dump $20 3 avail

Exaust manifold $30 2 Avail

Ignition Barrel with genuine key $30

inter cooler piping for front mout stainless. $20

Injectors in rail.. only 5 injectors. cant find the other atm.. injectors require clean because they been sitting aeound a while. $50

Throttle body s1 and s2 $40 each

s2 tps $30

Coil packs s1 $70

intercooler pipe with adapter for blitz blowoff valve. it can replace the standard pipe in that position $30

Gredy boost Gauge $30

Genuine oil filter $10

tomie 1.2 oil restrictors x2 $15 each

Standard intake pipe with blow off valve... one with out $30 each

cam gear cover $10

Oil cooler adapter with fittings $40

300zx oilcooler $10

genuine injector to manifold seals $10

Genuine rb25 headgasket 87mm bore $50

RB25 requires rebuild. belt came of at idle and broke 2 valves in cylinder 1. had 130000 ks, run fine before that, will come with good cams as it has been sitting around for a while and the lobes are pitted. comes with oil pump and harmonic balancer, $200

flywheel will need machining $20

Genuine inlet manifold gasket where it splits $30

charcoal canister $20

Washer Bottle with motors $30

wiper motor $30

coilpack cover $20

Maroon r33 wing make an offer... also have rear bumper

r33 dash make an offer.. welcome to come inspect

silicon right angle 2.5 inch bend $20

right angle fitting in pic (not speed flow) $10

Heat shields for manifold and turbo make an offer

complete inlet manifold with injectors, sensors, idle controll valve ect.. $200

top half of manifold x2 good for changing to a forward facing plenum $40 each

bottom part of manifold $10 requires new coolant outlet

plenum chamber $20

ALternator.. has been tested $70

power steer pump $50

standard turbo to airfilter pipe with adapter and k & n airfilter requires clean $30

some standard intake pipes in the pictures if you interested let me know and make an offer

please check the link for pictures http://www.boostcruising.com/forums/index....howtopic=384000

Link to comment
https://www.sau.com.au/forums/topic/255741-r33-skyline-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...